+352 27 63 53 92

customer-service@partao.com
14110

Case IH 14110 – Analogue Digital Instrument Cluster (ADIC): Transmission oil pressure configuration mismatch

Issue description

The electronic system has detected that the programmed configuration for the transmission oil pressure monitoring system does not match the physical hardware, sensor inputs, or expected parameters for the tractor's specific transmission type.

Applies to these machines

  • Maxxum
  • Farmall C
  • 85C
  • 95C
  • 105C
  • 115C
  • Farmall U
  • 105U
  • 115U
  • 5120
  • 5130
  • 5140
  • 5150
  • 5220
  • 5230
  • 5240
  • 5250
  • Magnum
  • Puma

Check the cause

  1. Verify ADIC Configuration: Access the ADIC settings using a dealer diagnostic tool to ensure the correct transmission type and sensor options are programmed into the cluster.

  2. Check Fluid Levels: Verify the transmission fluid level and condition, as erratic pressure readings can sometimes trigger pressure-related faults.

  3. Inspect the Sensor and Harness: Check the transmission oil pressure sensor circuit and connections to ensure the physical sensor matches the expected configuration and that the factory wiring harness is securely plugged in without damage.

Repair steps

  1. Access the Sensor

    If the ADIC configuration is correct but the hardware is mismatched or faulty, locate the transmission oil pressure sensor. This typically requires removing a small access panel to reach the sensor location on the transmission case.

  2. Remove the Old Sensor

    Disconnect the factory wiring harness from the sensor. Unscrew the old sensor from the transmission housing.

  3. Install the New Sensor

    Apply a dab of thread sealant to the threads of the new direct-replacement sensor and thread it right into the transmission case.

  4. Reconnect Wiring

    Plug the sensor directly into the factory wiring harness (no modifications should be needed if using the correct OEM part).

  5. Reprogram/Clear Codes

    If a new ADIC cluster was installed or the configuration was lost, reprogram the ADIC to match the physical transmission. Clear the 14110 fault code and test the tractor to ensure the code does not return.

Parts you might need

(18)

  • Transmission Oil Pressure Sensor

    121767A1

    Threads directly into the transmission case. Fits Maxxum, Magnum, and various other CNH models.

  • Transmission Oil Pressure Sensor

    1983225C1

    Threads directly into the transmission case. Fits Maxxum, Magnum, and various other CNH models.

  • Transmission Oil Pressure Sensor

    1983225C2

    Threads directly into the transmission case. Fits Maxxum, Magnum, and various other CNH models.

  • Transmission Oil Pressure Sensor

    1964832C1

    Threads directly into the transmission case. Fits Maxxum, Magnum, and various other CNH models.

  • Transmission Oil Pressure Sensor

    1964832C2

    Threads directly into the transmission case. Fits Maxxum, Magnum, and various other CNH models.

  • Transmission Oil Pressure Sensor

    87494633

    Threads directly into the transmission case. Fits Maxxum, Magnum, and various other CNH models.

  • Transmission Oil Pressure Sensor

    84078681

    Threads directly into the transmission case. Fits Maxxum, Magnum, and various other CNH models.

  • Transmission Oil Pressure Sensor

    87692837

    Threads directly into the transmission case. Fits Maxxum, Magnum, and various other CNH models.

  • Analogue Digital Instrument Cluster (ADIC)

    47365935

    Part numbers vary heavily depending on the exact tractor model and transmission options (e.g., Farmall vs. Magnum). Must be programmed to the specific tractor upon installation.

  • Analogue Digital Instrument Cluster (ADIC)

    47436477

    Part numbers vary heavily depending on the exact tractor model and transmission options (e.g., Farmall vs. Magnum). Must be programmed to the specific tractor upon installation.

  • Analogue Digital Instrument Cluster (ADIC)

    47130125

    Part numbers vary heavily depending on the exact tractor model and transmission options (e.g., Farmall vs. Magnum). Must be programmed to the specific tractor upon installation.

  • Analogue Digital Instrument Cluster (ADIC)

    47441086

    Part numbers vary heavily depending on the exact tractor model and transmission options (e.g., Farmall vs. Magnum). Must be programmed to the specific tractor upon installation.

  • Analogue Digital Instrument Cluster (ADIC)

    47364390

    Part numbers vary heavily depending on the exact tractor model and transmission options (e.g., Farmall vs. Magnum). Must be programmed to the specific tractor upon installation.

  • Analogue Digital Instrument Cluster (ADIC)

    47418399

    Part numbers vary heavily depending on the exact tractor model and transmission options (e.g., Farmall vs. Magnum). Must be programmed to the specific tractor upon installation.

  • Analogue Digital Instrument Cluster (ADIC)

    47641801

    Part numbers vary heavily depending on the exact tractor model and transmission options (e.g., Farmall vs. Magnum). Must be programmed to the specific tractor upon installation.

  • Analogue Digital Instrument Cluster (ADIC)

    48006628

    Part numbers vary heavily depending on the exact tractor model and transmission options (e.g., Farmall vs. Magnum). Must be programmed to the specific tractor upon installation.

  • Analogue Digital Instrument Cluster (ADIC)

    84602292

    Part numbers vary heavily depending on the exact tractor model and transmission options (e.g., Farmall vs. Magnum). Must be programmed to the specific tractor upon installation.

  • Analogue Digital Instrument Cluster (ADIC)

    90433711

    Part numbers vary heavily depending on the exact tractor model and transmission options (e.g., Farmall vs. Magnum). Must be programmed to the specific tractor upon installation.

Get help to fix this fault by requesting a quote

Browse other Case IH codes