DCU19109

Case IH DCU19109 – DCU: UREA Temperature Sensor in Tank Signal High

Issue description

The Dosing Control Unit (DCU) has detected an abnormally high voltage reading from the temperature sensor located within the Diesel Exhaust Fluid (DEF) tank. This indicates a potential short circuit to a power source in the sensor's wiring or an internal failure of the sensor itself, which compromises the Selective Catalytic Reduction (SCR) system's ability to monitor urea temperature and function correctly.

Applies to these machines

  • Magnum 190
  • Magnum 220
  • Magnum 240
  • Magnum 310
  • Magnum 370
  • Magnum 380
  • Puma
  • Maxxum 125 Pro
  • Quadtrac 370
  • Axial-Flow 8250
  • Axial-Flow 9230
  • Axial-Flow 9240
  • WD1203

Check the cause

  1. Visually inspect the wiring harness and connectors between the DCU and the DEF tank temperature sensor for chafing, melting, corrosion, or moisture intrusion.

  2. Scan for any other active or stored fault codes related to the SCR system for additional diagnostic clues.

  3. Verify DEF quality using a refractometer to ensure it meets the required 32.5% urea concentration (less likely to cause a signal high fault, but good practice).

  4. Check for DEF tank overheating conditions, such as a stuck open coolant control valve in the heating system, which can cause out-of-range temperature faults (fault code 19325).

  5. Disconnect the sensor and check the voltage at the sensor's connector with a digital multimeter; an unexpected high voltage reading indicates a short in the wiring harness.

  6. Test the sensor's internal resistance and compare it to manufacturer specifications to identify an internal sensor failure.

  7. Check for continuity in the wiring circuits and verify proper ground connections.

Repair steps

  1. Park and Secure the Machine

    Park the vehicle on a level surface, shut it down, and disconnect the batteries before beginning any repair work.

  2. Access the DEF Tank Sensor

    Depending on the machine, remove covers or lower the DEF tank to gain access to the sensor assembly.

  3. Drain the DEF Tank

    If the sensor assembly needs to be removed, drain the DEF from the tank.

  4. Disconnect and Remove the Sensor

    Disconnect the electrical connector from the sensor and unscrew the retaining ring to remove it.

  5. Inspect and Clean

    If there is significant crystallization on the sensor, try cleaning it with deionized water (note: cleaning may not resolve a 'signal high' electrical fault).

  6. Replace the Sensor

    If the diagnostic checks point to a faulty sensor, replace the entire integrated DEF sensor assembly.

  7. Repair Wiring

    If the diagnostic checks reveal a short or open in the wiring harness, repair or replace the damaged section of the harness.

  8. Reassemble and Refill

    Reinstall the sensor and any other components that were removed. Refill the DEF tank with fresh, high-quality DEF.

  9. Clear Fault Codes and Test

    Reconnect the batteries, start the machine, use a diagnostic tool to clear the fault code, and operate the machine to ensure the fault does not return.

Parts you might need

(11)
  • Urea Sensor5802862328

    OEM Case IH integrated DEF sensor assembly

  • Remanufactured Urea Sensor

    5802862328R

    Remanufactured OEM alternative

  • DEF Tank Sensor Assembly

    Generic replacement reductant tank temperature sensor

  • Urea Temperature Sensor

    Generic replacement part name

  • Reductant Tank Temperature Sensor

    Generic replacement part name

  • DEF Head Unit / DEF Tank Sending Unit

    KBH17371

    Common Case IH / New Holland DEF Head Unit. Includes integrated level, temperature, and quality sensors. Must order using the machine's specific serial number.

  • Must order using the machine's specific serial number.

  • DEF Tank Sending Unit

    84260414

    Sender Units for specific loaders/tractors. Must order using the machine's specific serial number.

  • Sender Units for specific loaders/tractors. Must order using the machine's specific serial number.

  • CNH Remanufactured ATS Sensor

    47512679R

    Must order using the machine's specific serial number.

  • CNH Remanufactured ATS Sensor

    47512702R

    Must order using the machine's specific serial number.

Get help to fix this fault by requesting a quote

Browse other Case IH codes