EHR4140

Case IH EHR4140 – EHR: Rear Remote No.3 Spool Cannot Return to Neutral

Issue description

The electronic control system has detected that the spool for the number three rear electro-hydraulic remote (EHR) valve is failing to return to its neutral position. The system commands the valve to center itself, but the position sensor on the valve reports that the spool has not reached the neutral (centered) position within the expected timeframe. This condition can lead to unintended hydraulic flow, prevent the proper operation of the associated hydraulic function on the attached implement, and may lock out all hydraulic functions until the tractor is restarted.

Applies to these machines

  • Magnum 235
  • Magnum 290
  • Magnum 315
  • Magnum 340
  • Puma 130
  • Puma 145
  • Puma 160
  • Puma 165
  • Puma 180
  • Puma 195
  • Puma 210
  • Optum
  • Steiger

Check the cause

  1. Check hydraulic oil for contamination or debris from an implement, which can cause the spool to stick

  2. Inspect the wiring harness and connectors leading to the number three remote valve for chafed wires, corrosion, or damage (especially in articulation areas)

  3. Check the valve stack bolt torque, as incorrect torque can distort the valve body and cause the spool to bind

  4. Verify software and calibration status, as a software update or recalibration may be required

  5. Swap the electronic pilot head from remote #3 with an adjacent functioning remote (e.g., #4). If the fault code follows the pilot head (e.g., EHR4154), the pilot head is faulty. If EHR4140 remains, the issue is likely mechanical (sticking spool) or a wiring issue specific to that circuit.

Repair steps

  1. Ensure safety and relieve pressure

    Park the tractor on a level surface, shut down the engine, and relieve all hydraulic pressure from the circuits before beginning work.

  2. Clean the work area

    Thoroughly clean the area around the #3 remote valve to prevent dirt from entering the hydraulic system during disassembly.

  3. Address contamination

    If contamination is suspected, disconnect the hydraulic lines and remove the spool from the valve body for cleaning. Perform a complete hydraulic system flush and filter change if contamination is severe.

  4. Repair wiring

    If wiring faults were found during inspection, repair or replace damaged harness sections and ensure connectors are clean, secure, and free of corrosion.

  5. Replace faulty components

    If the component swap test identified a faulty pilot head/solenoid assembly, replace it. If the valve spool is mechanically binding and cannot be rectified by cleaning, replace the entire valve slice.

  6. Reassemble and torque

    Reassemble all components. If the valve stack was loosened or disassembled, ensure it is torqued to the manufacturer's specifications to prevent spool binding.

  7. Calibrate remote valves

    Perform a mandatory remote valve calibration using the tractor's diagnostic H-menus or a dealer service tool to electronically synchronize the control lever with the valve spool.

Parts you might need

(9)
  • Electronic actuator controlling the spool. Replace if internal position sensor or solenoid coils fail.

  • Rear Remote Electro-Hydraulic Valve Pilot Head / Solenoid Valve

    87723774

    Electronic actuator controlling the spool. Replace if internal position sensor or solenoid coils fail.

  • Mechanical part containing the spool. Replace if spool is physically damaged or sticking due to wear/distortion.

  • Rear Remote Hydraulic Control Valve / Valve Slice

    A169029

    Control valve for older models. Replace if spool is physically damaged or sticking due to wear/distortion.

  • Rear Remote Hydraulic Control Valve / Valve Slice Kit

    719357595

    3rd remote valve kit.

  • Remanufactured Hydraulic Remote Valve Assembly

    87384974R

    Fits various Magnum/MX models

  • EHR Control Lever / Joystick (Armrest)

    84184612C

    If the cab switch is the culprit

  • EHR Control Lever / Joystick (Armrest)

    47372893R

    If the cab switch is the culprit

Get help to fix this fault by requesting a quote

Browse other Case IH codes