Case IH EHR4219 – EHR (ARM / XCM): Rear Remote No.4 Valve Spool Not Calibrated
Issue description
This code indicates that the control system does not have a valid calibration saved for the 4th rear auxiliary hydraulic remote valve. This can happen if the calibration data is lost, if a new uncalibrated controller/valve was installed, or if a hardware failure (such as a faulty armrest potentiometer or sticking valve spool) is preventing the system from successfully completing the calibration sweep.
Applies to these machines
13 machines- Magnum 235
- Magnum 305
- Magnum 340
- Puma 140
- Puma 155
- Puma 160
- Puma 165
- Puma 180
- Puma 195
- Puma 210
- Puma 225 CVX
- Steiger Series
- Quadtrac Series
Check the cause
Inspect the wiring harness and electrical connectors leading to the number 4 remote valve for damage, corrosion, or loose connections (pay close attention to the articulation point on articulating tractors for chafing)
Check for other active fault codes, as a failing potentiometer in the armrest control lever can sometimes trigger this fault
Inspect the valve and its connections for any hydraulic fluid leaks
Ensure the hydraulic fluid is warmed to at least 50-60°C (140°F) before attempting calibration, as temperature affects the process
Repair steps
Armrest Control Calibration
With the key off, press and hold the 'program' key on the armrest. While holding the program key, turn the ignition key to the 'on' position.
Navigate to Calibration Menu
Use the arrow keys to scroll through the menu to 'ARM' (or a similar armrest setting) and select it. Scroll to the auxiliary lever ('ox lever') calibration option and select it.
Perform Lever Calibration
Follow the on-screen instructions, which typically involve moving the remote levers one at a time to their full forward and rearward positions. Once complete, exit the menu, turn the key off, wait 30 seconds, and restart the tractor to test.
EHR Valve Calibration (Diagnostic Tool)
If armrest calibration fails, warm the hydraulic fluid to the recommended temperature. Connect the Case IH diagnostic tool (calibration cable) to the diagnostic port (often located near the passenger seat or under the cab), navigate to the EHR calibration settings in the software, and follow the guided process for each valve.
EHR Valve Addressing (For New Valves)
If a new valve has been installed, it must be addressed. Turn the key on, enter the 'H' menu, and navigate to the 'HL' function. Connect each remote valve one at a time until an audible tone is heard. Activate the number one timer switch three times until the display shows 'end', then turn the key off to save.
Replace Faulty Components
If calibration repeatedly fails, it indicates a faulty component. Replace the armrest lever potentiometer or the valve solenoid as indicated by diagnostics.
Parts you might need
(12)Remote Control Valve Assembly
84398218Example part number for Puma series
- Remote Control Valve Assembly84230181
Example part number for Maxxum/Puma series
Remote Control Valve Assembly
A169029Example part number for various models
- Remote Control Valve Assembly1980447C8
Example part number for 5100/5200 series
- Armrest Potentiometer87605245
Control lever sensor, replaces multiple older numbers
- Armrest PotentiometerA186061
Example part number for older Magnum series
- Armrest Potentiometer92265125
Example part number for older Magnum series, replaces 111448A1, A186003
- Solenoid Valve100739A1
Highly specific to the fitted valve
- Solenoid Valve139307A1
Highly specific to the fitted valve
- Solenoid Valve81870291
Highly specific to the fitted valve
Remote Valve Main Spool (Updated)
47429154Updated spool featuring an additional hydraulic oil bleed to resolve surging/erratic flow issues.
Generic fitment example; exact part number varies heavily by armrest generation and tractor model.
Get help to fix this fault by requesting a quote