EHR4327

Case IH EHR4327 – RK/RL or ARM: Rear Remote No.7 Spool Cannot Return to Neutral

Issue description

The control module has detected that the spool within the seventh rear electro-hydraulic remote (EHR) valve has failed to return to its neutral position after a command. This indicates a mechanical or electrical failure preventing the spool from centering, which can halt the operation of that specific remote and potentially affect the proper operation of the associated mechanism and the entire hydraulic system.

Applies to these machines

  • Puma 115
  • Puma 125
  • Puma 130
  • Puma 140
  • Puma 155
  • Puma 160
  • Puma 165
  • Puma 180
  • Puma 195
  • Puma 210
  • Puma 225
  • Magnum
  • Steiger

Check the cause

  1. Relieve hydraulic pressure by parking on a level surface, lowering implements, shutting down the engine, and cycling the hydraulic remote levers

  2. Inspect hydraulic fluid level and condition for contamination (milky, dark, or containing debris), which is a leading cause of sticking valve spools

  3. Check for external mud, ice, or debris around the No. 7 remote valve and its linkage that could physically obstruct spool movement

  4. Inspect the wiring harness and connectors leading to the No. 7 remote valve solenoid for signs of damage, corrosion, or loose connections

  5. Perform a solenoid electrical test (resistance and voltage) to check for open circuits, short circuits, or a lack of voltage from the controller

  6. Attempt to move the spool manually using the manual override pin (if equipped) to differentiate between a mechanical jam and an electrical issue

  7. Check for a stuck detent mechanism (broken spring or jammed detent) that can prevent the spool from returning to neutral

  8. Swap the solenoid from the faulty No. 7 valve with a known good one from an adjacent valve, or swap control lever electrical connections, to see if the problem follows the component

  9. Perform a remote valve calibration through the instrument panel or diagnostic tool to resolve potential lever/spool position disagreement

Repair steps

  1. Safety First

    Ensure all hydraulic pressure is relieved and the tractor is safely shut down.

  2. Access the Valve

    Remove any covers or guards to gain access to the rear of the remote valve stack.

  3. Remove the Detent Housing

    Unscrew the large pipe or detent housing from the back of the valve section corresponding to remote No. 7. This may require a large socket.

  4. Extract the Spool Assembly

    Once the rear housing is unscrewed, the entire spool and actuator assembly can be carefully pulled out from the back of the valve body. Be prepared for some residual hydraulic fluid to spill.

  5. Disassemble the Spool

    Carefully clamp the spool assembly in a vise. Unscrew the end plug, being mindful of a spring that may be under slight compression. Remove the spring, ball cup, and detent balls, often with the help of a small magnet. Unscrew the actuator from the end of the spool. Note the orientation of all components, including springs and washers, as you disassemble.

  6. Inspect and Clean

    Thoroughly clean all components with a suitable solvent and inspect for damage. Look for scoring or burrs on the spool itself, broken or weak springs, debris or metal shavings inside the actuator or valve body, and worn or damaged O-rings and seals.

  7. Reassembly

    Replace any worn or damaged components, especially O-rings and seals from a seal kit. Reassemble the spool mechanism in the reverse order of disassembly, ensuring all balls, springs, and pistons are correctly seated. Use a clean assembly lube on O-rings to prevent damage during installation. Carefully insert the reassembled spool back into the valve body. Thread the detent housing back into the valve and tighten it to the manufacturer's specification.

  8. Final Testing

    After reassembly, start the tractor, allow the hydraulic system to warm up, and test the function of the repaired remote valve. Check for leaks and ensure the fault code does not reappear. A valve calibration may be necessary after the repair.

Parts you might need

(4)
  • Complete Valve Section (Slice)

    87325955

    Common valve assembly part number for Puma models, often superseded or with variations. Verify fitment.

  • Alternative part numbers include 87472229 (supersedes to 87723774) and 90445340 (replaces 87749159).

  • Valve Spool

    Not typically sold separately. Often included in the complete valve slice.

  • Seal Kit

    Order based on the specific valve model from a Case IH dealer.

Get help to fix this fault by requesting a quote

Browse other Case IH codes