ENG546

Case IH ENG546 – ECU: Fuel Pressure Sensor Voltage Is Too High

Issue description

The Engine Control Module (ECU) has detected a voltage signal from the fuel pressure sensor that exceeds the manufacturer's predefined maximum limit. This indicates that the sensor is reporting a voltage higher than expected, which is typically caused by a short circuit to a power source in the wiring harness, a faulty fuel pressure sensor, or an internal ECU fault. The ECU relies on this sensor data to regulate fuel delivery, meaning this fault can directly impact optimal engine performance.

Applies to these machines

  • Farmall 90C
  • Farmall 95A
  • Farmall 100C
  • Farmall 105A
  • Farmall 110C
  • Farmall 110U
  • Farmall 115A
  • Farmall 120C
  • Farmall 120U
  • Maxxum 110
  • Maxxum 115
  • Magnum
  • Steiger
  • 2377 Combine
  • 2388 Combine
  • Models with 6TAA-8304 and 6TAA-9004 8.3L and 9.0L engines
  • JX95
  • Models using Kohler engines

Check the cause

  1. Inspect the fuel pressure sensor and wiring harness for visible damage, chafing, corrosion, oil or coolant contamination, and loose connections.

  2. Check for other active fault codes, particularly those related to low system voltage or other sensors, which can cause erroneous readings.

  3. Test the ground circuit to ensure it is clean and secure, as a poor ground can cause a faulty signal.

  4. Check continuity and resistance in the wiring between the sensor connector and the ECU using a digital multimeter.

  5. Backprobe the sensor's signal wire at the ECU connector to measure voltage; a reading stuck high (e.g., 5 volts) or unchanging with engine conditions indicates a circuit or sensor issue.

  6. Connect a mechanical pressure gauge to the fuel rail test port and compare its reading to the live electronic data on a diagnostic scan tool to verify if the sensor reading is falsely high.

Repair steps

  1. Relieve fuel system pressure

    For safety, always relieve the pressure in the fuel system before disconnecting any fuel lines or components.

  2. Perform diagnostic checks

    Follow the diagnostic steps listed above to isolate the root cause of the fault.

  3. Address wiring issues

    If diagnostics reveal a short to power, open circuit, or corroded connector, repair or replace the damaged section of the harness. Clean any corroded connectors with electrical contact cleaner.

  4. Replace fuel pressure sensor

    If the sensor is confirmed faulty, disconnect the electrical connector, unscrew the old sensor from the fuel rail, and install the new sensor. Torque to manufacturer specifications (e.g., 50 Nm for 8.3L and 9.0L engines). Reconnect the harness.

  5. Clear codes and verify

    Clear the stored fault codes from the ECU using a diagnostic tool. Start the engine and perform a road test or operate under load to ensure the fault does not return.

Parts you might need

(19)
  • Used on a variety of Case IH models

  • Listed for several Farmall C, A, and U models

  • Associated with Maxxum models

  • Associated with Maxxum models

  • Fuel Pressure Sensor

    2859145

    Associated with Maxxum models

  • Case IH / CNH OEM. Always verify exact part number against Engine Serial Number (ESN).

  • Case IH / CNH OEM. Always verify exact part number against Engine Serial Number (ESN).

  • Case IH / CNH OEM. Always verify exact part number against Engine Serial Number (ESN).

  • Case IH / CNH OEM. Always verify exact part number against Engine Serial Number (ESN).

  • Case IH / CNH OEM. Always verify exact part number against Engine Serial Number (ESN).

  • Fuel Rail Pressure Sensor / Fuel Delivery Pressure Sensor

    4307165

    Cummins OEM. Always verify exact part number against Engine Serial Number (ESN).

  • Fuel Rail Pressure Sensor / Fuel Delivery Pressure Sensor

    4954245

    Cummins OEM. Always verify exact part number against Engine Serial Number (ESN).

  • Fuel Rail Pressure Sensor / Fuel Delivery Pressure Sensor

    3974092

    Cummins OEM. Always verify exact part number against Engine Serial Number (ESN).

  • Fuel Rail Pressure Sensor / Fuel Delivery Pressure Sensor

    5260246

    Cummins OEM. Always verify exact part number against Engine Serial Number (ESN).

  • Fuel Rail Pressure Sensor / Fuel Delivery Pressure Sensor

    5297641

    Cummins OEM. Always verify exact part number against Engine Serial Number (ESN).

  • Fuel Rail Pressure Sensor / Fuel Delivery Pressure Sensor

    0281006165

    Bosch OEM. Bosch is the primary OEM manufacturer. Ensure genuine OEM sensor.

  • Fuel Rail Pressure Sensor / Fuel Delivery Pressure Sensor

    0281006325

    Bosch OEM. Bosch is the primary OEM manufacturer. Ensure genuine OEM sensor.

  • Fuel Rail Pressure Sensor / Fuel Delivery Pressure Sensor

    0281006226

    Bosch OEM. Bosch is the primary OEM manufacturer. Ensure genuine OEM sensor.

  • Fuel Rail Pressure Sensor / Fuel Delivery Pressure Sensor

    0281006087

    Bosch OEM. Bosch is the primary OEM manufacturer. Ensure genuine OEM sensor.

Get help to fix this fault by requesting a quote

Browse other Case IH codes