INST12071

Case IH INST12071 – ICU: Communications Lost with Transmission Controller

Issue description

The system has detected a loss of communication between the Instrument Cluster Controller (ICU) and the Transmission Control Unit (TCU) on the CAN bus network. This interruption prevents the instrument cluster from receiving transmission data, which can lead to a loss of transmission-related functions, affect vehicle performance, and trigger warnings on the operator's display. This is typically caused by wiring issues, a faulty controller, or problems with the CAN bus network itself.

Applies to these machines

  • MX210
  • MX230
  • MX255
  • MX285
  • TG210
  • TG230
  • TG255
  • TG285

Check the cause

  1. Check the diagnostic display for any other active or stored fault codes across all controllers, as multiple codes may indicate a widespread CAN bus issue

  2. Inspect all fuses, particularly 5-amp fuses related to the controllers and electrical system, for blown components

  3. Verify that both the Transmission Controller and Instrument Cluster are receiving correct voltage and have solid ground connections

  4. Visually inspect the wiring harness and connectors between the Instrument Cluster and Transmission Controller for chafing, corrosion, or bent pins

  5. With the key off, measure CAN bus resistance between the CAN high and CAN low wires (typically yellow and green). It should be approximately 60 ohms; 120 ohms indicates a missing terminating resistor, while significantly lower indicates a short or faulty controller

Repair steps

  1. Address other faults

    Diagnose and repair any other present fault codes first, as they may be the root cause of the communication loss.

  2. Repair wiring and connectors

    Repair or replace any damaged wiring or corroded connectors found during inspection. Ensure all connections are clean and secure.

  3. Check and replace terminating resistors

    If CAN bus resistance is incorrect (e.g., 120 ohms), locate and test the terminating resistors. On some models, the transmission controller itself may act as a terminating resistor. Replace any faulty terminators.

  4. Isolate the faulty module

    If wiring and terminators are good, disconnect other controllers from the CAN bus one at a time to see if communication with the transmission controller is restored.

  5. Update or replace Transmission Controller

    If the TCU is identified as faulty, check if a software update resolves the issue. If not, replace the Transmission Controller. It is recommended to have a Case IH dealer confirm the diagnosis before replacing a costly controller.

Parts you might need

(20)
  • Transmission Control Module (TCU)

    86985266

    For MX210, MX230, MX255, MX285. Superseded by other numbers.

  • Transmission Control Module (TCU)

    313859A1

    Potential replacement/supersession for 86985266.

  • Transmission Control Module (TCU)

    86990264

    Potential replacement/supersession for 86985266.

  • Transmission Control Module (TCU)

    87352198

    Potential replacement/supersession for 86985266.

  • Transmission Control Module (TCU)

    87350683

    Potential replacement/supersession for 86985266.

  • Transmission Control Module (TCU) - Remanufactured

    87617963R

    Remanufactured option for MX210, MX230, MX255, MX285.

  • Transmission Control Module (TCU)

    447256A2

    For some MX210 models. Discontinued.

  • Substitute for discontinued 447256A2. Requires additional harness 84180381.

  • Additional harness required when substituting TCU 447256A2 with 84166771.

  • Engine Control Unit (ECU)

    J944125

    Listed for TG255, TG285. Note: Transmission controller part number may differ.

  • Wiring Harness

    Specific to tractor model and harness section.

  • CAN Bus Terminating Resistor

    Source from dealer to ensure correct specifications.

  • Transmission Controller (TCM / TRANS Module)

    87617962

    Often available as remanufactured units from aftermarket electronics rebuilders (e.g., Titan Systems, UpFix) due to OEM obsolescence on older MX models.

  • Transmission Controller (TCM / TRANS Module)

    87364400

    Often available as remanufactured units from aftermarket electronics rebuilders (e.g., Titan Systems, UpFix) due to OEM obsolescence on older MX models.

  • Transmission Controller (TCM / TRANS Module)

    87393071

    Often available as remanufactured units from aftermarket electronics rebuilders (e.g., Titan Systems, UpFix) due to OEM obsolescence on older MX models.

  • Often available as remanufactured units from aftermarket electronics rebuilders (e.g., Titan Systems, UpFix) due to OEM obsolescence on older MX models.

  • Transmission Controller (TCM / TRANS Module)

    87560224

    Often available as remanufactured units from aftermarket electronics rebuilders (e.g., Titan Systems, UpFix) due to OEM obsolescence on older MX models.

  • Transmission Controller (TCM / TRANS Module)

    87567055

    Often available as remanufactured units from aftermarket electronics rebuilders (e.g., Titan Systems, UpFix) due to OEM obsolescence on older MX models.

  • Often available as remanufactured units from aftermarket electronics rebuilders (e.g., Titan Systems, UpFix) due to OEM obsolescence on older MX models.

  • Transmission Controller (TCM / TRANS Module)

    1964862C2

    Often available as remanufactured units from aftermarket electronics rebuilders (e.g., Titan Systems, UpFix) due to OEM obsolescence on older MX models.

Get help to fix this fault by requesting a quote

Browse other Case IH codes