Case IH NH10024 – Transmission Control Module (TCM), Suspension Control Module, Central Controller (XCM), or Universal Control Module (UCM): Front Suspension Not Calibrated
Issue description
The front suspension system has not been successfully calibrated, which may negatively affect the performance, ride quality, and stability of the tractor. This calibration is a necessary procedure for the control module to learn the operational range and parameters of the front suspension components. An uncalibrated system disables automatic suspension functions and can be triggered by the installation of a new component, a memory reset, or an underlying hardware issue preventing the calibration from completing.
Applies to these machines
8 machines- Magnum 250
- Magnum 305
- Magnum 310
- Magnum 335
- Magnum 340
- Puma 165
- Puma 180-260 CVX
- MXM 120-190
Check the cause
Check the diagnostic menu for other active or stored fault codes (e.g., 'U' codes like U01, U02, U03, U04 or 'L' codes) that indicate a specific component failure preventing calibration
Verify the front suspension pressure sensors read 0 psi (monitor via the 'Trans FSUS' menu on the A-Post display). If not zero, manually relieve pressure using thumb screws on the suspension control valve
Visually inspect the front axle position sensor and linkage for damage, corrosion, disconnection, or seizing. Verify sensor voltage (e.g., 1.05V to 3.86V on Puma models)
Check that hydraulic oil is at the correct operating temperature for calibration (e.g., 20-50°C for MXM models)
Inspect the wiring harness and connectors to the suspension control valve, position sensor, and pressure sensors for damage, corrosion, or loose connections
Ensure the front suspension mode is enabled in the tractor's 'H' menu (e.g., H3 menu on a New Holland T7), as it may default to disabled after a module reset
Repair steps
Park and prepare tractor
Park the tractor on a level surface and engage the parking brake.
Access diagnostic menu
Install the special diagnostic connector/jumper into the service port and turn the ignition key to the 'ON' position to activate the 'H' menu on the display.
Navigate to calibration
Use the instrument panel menus to scroll through the 'H' menus, locate, and select the front suspension calibration menu (often designated as 'H1').
Initiate calibration sequence
Start the engine and set the speed to approximately 1200 RPM. Follow the on-screen prompts to begin; the tractor will automatically raise and lower the suspension to learn minimum and maximum positions.
Monitor calibration
Watch the display for the 'CAL' message. If the calibration fails, note any 'cal failed' message or specific 'U' codes displayed (e.g., 'U07' if the suspension is stationary during the raise command) to diagnose the point of failure.
Store calibration values
Once the 'END' message appears, turn the ignition key off to store the new calibration values in the control module's memory, then remove the diagnostic connector.
Parts you might need
(12)- Front Axle Position Sensor429690A1
Used on various Magnum and Puma models. A failed or improperly adjusted position sensor is a common cause of calibration failure.
- Front Axle Position Sensor87605245
Used on various Magnum and Puma models. A failed or improperly adjusted position sensor is a common cause of calibration failure.
Front Axle Position Sensor
87380892Used on various Magnum and Puma models. A failed or improperly adjusted position sensor is a common cause of calibration failure.
- Front Suspension Pressure Sensor84409605
Measures hydraulic pressure in suspension cylinders. A faulty sensor can prevent the system from correctly reading pressure values.
- Front Suspension Pressure Sensor375644A1
Measures hydraulic pressure in suspension cylinders. A faulty sensor can prevent the system from correctly reading pressure values.
- Front Suspension Pressure Sensor86987513
Measures hydraulic pressure in suspension cylinders. A faulty sensor can prevent the system from correctly reading pressure values.
- Front Suspension Pressure Sensor84130918
Measures hydraulic pressure in suspension cylinders. A faulty sensor can prevent the system from correctly reading pressure values.
Front Suspension Accumulator
Faulty accumulators with bad bladders can prevent successful calibration.
210 Bar, 1 Litre capacity. Fits Case IH Puma, Maxxum, Farmall, and New Holland T6/T7 series.
Front Axle / Suspension Valve Component
316330A2
Get help to fix this fault by requesting a quote