NH1015

Case IH NH1015 – EDC or XCM: R/H Load Sensing Pin Signal Too High

Issue description

The load sensing pins (draft pins) are electronic sensors located at the lower link arms of the rear 3-point hitch. They measure the draft (pulling force) exerted by an implement. A "signal too high" condition means the voltage returning from the right-hand sensor to the controller is exceeding the normal operating range. This typically indicates a short circuit to power (+Ve voltage) in the wiring harness, or an internal failure of the sensor itself.

Applies to these machines

  • Puma Series
  • Puma 140
  • Puma 150
  • Puma 165
  • Maxxum Series
  • Magnum Series
  • Farmall 115U Pro
  • T7 Series
  • T7.210
  • T7.220
  • T7.235
  • T7.250
  • T7.260
  • T7.270
  • TM Series
  • T6000 Series

Check the cause

  1. Visually inspect the wiring harness and connector leading to the right-hand load sensing pin for damage, chafing, melted insulation, corrosion, moisture, or pushed-out pins.

  2. Check for a short to power: Disconnect the harness, turn the key to the 'on' position, and measure voltage between the harness pins and chassis ground. If the signal wire shows battery voltage (12V+), there is a short to power in the harness.

  3. Check for sensor internal shorts: With the sensor disconnected, measure resistance between the signal pin and the power/ground pins on the sensor. A very low resistance reading indicates an internal short.

  4. Perform a swap test: Swap the left and right load sensing pins. If the fault code changes to NH1016 or NH1017, the right-hand pin is faulty. If NH1015 persists, the issue is in the wiring harness or control module.

Repair steps

  1. Isolate the fault

    Perform diagnostic checks to determine if the fault is in the wiring harness or the load sensing pin itself.

  2. Repair wiring harness

    If a short circuit is found, repair the damaged section by replacing wire, repairing the connector, or re-insulating exposed wires. Seal all repairs against moisture.

  3. Replace load sensing pin

    If the pin is faulty, it must be replaced. The pin is typically located at the attachment point of the lower three-point hitch arm to the tractor's rear axle housing. Securely support the lower lift arm, remove retaining clips or bolts, and drive out the old pin (this may require a hammer and a drift). Install the new load sensing pin in the correct orientation, reconnect the electrical connector, and secure the pin with its retaining hardware.

  4. Clear fault codes

    Clear the fault codes from the hitch control module using a diagnostic tool or the instrument cluster display.

  5. Perform hitch calibration

    After replacing the pin or repairing the circuit, perform a hitch calibration procedure as specified in the machine's manual.

Parts you might need

(11)
  • Right-Hand Load Sensing Pin

    44503

    Listed for Case IH Puma and New Holland T7 series tractors

  • Hitch Pin232616A3

    Supersedes part numbers 87773620 and 441594A1

  • Pin Eliminator Kit

    AMX33142

    Aftermarket bypass kit; disables automatic draft control

  • Pin Eliminator Kit

    HA87661289

    Aftermarket bypass kit; disables automatic draft control

  • Draft Load Sensing Pin Elimination Kit

    305135A1

    These kits usually come with two dummy modules (to eliminate both left and right pins simultaneously) and zip ties to secure the harness.

  • Draft Load Sensing Pin Elimination Kit

    1964916C3

    These kits usually come with two dummy modules (to eliminate both left and right pins simultaneously) and zip ties to secure the harness.

  • Draft Load Sensing Pin Elimination Kit

    47137583

    These kits usually come with two dummy modules (to eliminate both left and right pins simultaneously) and zip ties to secure the harness.

  • These kits usually come with two dummy modules (to eliminate both left and right pins simultaneously) and zip ties to secure the harness.

  • Draft Load Sensing Pin Elimination Kit

    8302386

    Includes two electronic modules and tie wraps to bypass both the left and right pins simultaneously. Verify specific model fitment when ordering.

Get help to fix this fault by requesting a quote

Browse other Case IH codes