NH2027

Case IH NH2027 – TCU: Engine Speed Too Low

Issue description

The transmission control module has detected that the engine speed is below the minimum required threshold for a requested operation, such as a gear shift. This lack of sufficient RPM can prevent adequate hydraulic pressure, potentially causing stalling or damage to transmission components during engagement. It may affect overall machine performance and indicates an underlying issue with operator procedure, the engine, or its control system.

Applies to these machines

  • Magnum 180
  • Magnum 200
  • Magnum 215
  • Magnum 220
  • Magnum 225
  • Magnum 235
  • Magnum 240
  • Magnum 250
  • Magnum 255
  • Magnum 280
  • Magnum 305
  • Magnum 310
  • Magnum 335
  • Magnum 340
  • Magnum 380
  • Maxxum 115
  • Maxxum 125
  • Maxxum 135
  • Maxxum 145
  • Maxxum 150
  • Puma 150
  • Puma 165
  • Puma 185
  • Puma 200
  • Puma 215
  • Puma 220
  • Puma 230
  • Puma 240
  • MX210
  • MX230
  • MX240
  • MX255
  • MX305
  • AFX8010

Check the cause

  1. Verify operator procedure to ensure adequate engine RPM is being maintained during transmission-related operations

  2. Visually inspect the wiring harness and connectors between the engine speed sensor and the transmission controller for damage, corrosion, or loose connections

  3. Test the engine speed sensor's output functionality using a multimeter

  4. Check for other related fault codes (such as ENG 115, transmission controller communication, or sensor power supply) that could indicate a root cause

Repair steps

  1. Adjust operator procedure

    Ensure the engine is operated at a higher throttle setting during hydraulic functions or powershifting to maintain adequate RPM for the transmission.

  2. Inspect and repair wiring

    Check the wiring harness and connectors between the engine speed sensor and the TCU. Repair any damaged wires, clean corrosion, and secure loose connections.

  3. Test or replace engine speed sensor

    Test the sensor output with a multimeter or swap with a known good sensor. If faulty, replace the engine speed sensor (or transmission speed sensor, depending on the specific model's configuration).

  4. Update software and calibrate

    If the fault persists and hardware is functional, have a certified technician perform a software update or recalibration of the transmission controller.

Parts you might need

(11)
  • OEM Case IH. Also referred to as crankshaft position sensor or engine RPM sensor.

  • Aftermarket (Abilene Machine). Replaces OEM 2853552 and 87803075.

  • Transmission Speed Sensor

    47130773

    Aftermarket (ASAP). Fits various Magnum, Maxxum, and Puma models. Replaces OEM 5180162, 87564756, 82028157.

  • Aftermarket (FridayParts). Fits Magnum and MX series. Replaces OEM 87422106 and 87548198.

  • Transmission Speed Sensor

    QTP-400087

    Aftermarket (SutterBros). For Case IH Magnum and MX series.

  • Fits Case IH Farmall, Maxxum, Puma, Optum

  • Magnetic Induction/Hall Effect RPM Speed Sensor for Puma, Optum, Magnum CVT/PowerShift

  • Transmission Speed Sensor

    84141151

    Magnetic Induction/Hall Effect RPM Speed Sensor for Puma, Optum, Magnum CVT/PowerShift

  • Fits Case IH Magnum 180-380, Puma 165

Get help to fix this fault by requesting a quote

Browse other Case IH codes