Case IH NH4101 – Rear Electronic Hydraulic Remote Valves controller: Remote No.1 Control Message Not Plausible
Issue description
The system has detected that the Remote No.1 Control Message is not plausible, indicating an issue with the communication or integrity of the message. Specifically, the control module for the number 1 rear electro-hydraulic remote valve has detected an invalid or corrupted message on the CAN bus. This means commands sent from the operator's control (armrest controller) are not being correctly interpreted by the valve's electronic controller due to data corruption, signal interference, or a timing issue.
Applies to these machines
13 machines- Puma 160
- Puma 210
- Maxxum 115
- Maxxum 125
- T7.170
- T7.185
- T7.200
- T7.210
- T7.220
- T7.235
- T7.250
- T7.260
- T7.270
Check the cause
Verify battery and system voltage, as low voltage is a frequent cause of CAN bus communication errors
Inspect the wiring harness and connectors between the armrest controls, main tractor controller, and No. 1 rear remote valve for corrosion, moisture intrusion, physical damage, or loose connections
Check for other active fault codes that might indicate a broader CAN bus communication failure rather than a single component issue
Use an Electronic Service Tool (EST) or equivalent diagnostic software to monitor the CAN bus in real-time and confirm if the remote valve controller is online
Repair steps
Address related faults
If other CAN bus or voltage-related fault codes are present, diagnose and repair them first before proceeding.
Clean and secure connections
Disconnect the electrical connectors at the armrest controller and the No. 1 remote valve. Clean the pins and receptacles with electrical contact cleaner, ensure they are dry, and reconnect securely.
Test CAN bus integrity
If you have access to a multimeter with CAN diagnostic capabilities or an oscilloscope, check the CAN high and low line voltages and resistance. With the system powered down, a healthy CAN bus typically has a resistance of around 60 ohms between the high and low lines. Deviations indicate a wiring issue or a faulty terminating resistor.
Isolate the component
If the tractor has multiple identical remote valves, swap the electronic control portion of the No. 1 valve with another (e.g., No. 2). If the fault code changes to indicate the other valve (e.g., NH4115), it strongly suggests the valve controller itself is faulty.
Replace faulty component
If diagnostic checks point to a faulty component, replace the remote valve's electronic controller/solenoid or the armrest control unit.
Clear codes and calibrate
After repair, clear all fault codes using a diagnostic tool. Recalibrate the electronic hydraulic remote valves if required by the system.
Parts you might need
(11)Fits Case IH Maxxum (100-150) and Puma (115-165) series, as well as New Holland T6 and T7 series tractors.
Fits Case IH Puma 130, 145, and 160 CVT models (2010 onwards). Remanufactured part number is 84175671R.
General remote control valve, fitment must be checked against the specific machine's serial number.
Complete Rear Remote Valve Assembly
47595558Fits Magnum 235-380 and Steiger 350-600
Complete Rear Remote Valve Assembly
47434188Fits Magnum 235-380 and Steiger 350-600
Complete Rear Remote Valve Assembly
87486189Fits Magnum 235-380 and Steiger 350-600
Replaces older numbers 5190713, 5195165, 87779662 for various Magnum/Puma models
Complete Rear Remote Valve Assembly (Older)
5190713Replaced by 87526168
Complete Rear Remote Valve Assembly (Older)
5195165Replaced by 87526168
Complete Rear Remote Valve Assembly (Older)
87779662Replaced by 87526168
EHR Control Valve Wiring Harness (4-Spool)
84151662If the diagnostic check reveals a shorted harness on Steiger models
Get help to fix this fault by requesting a quote