NH4144

Case IH NH4144 – Hydraulic/Transmission Module: Remote No.4 EEPROM Error

Issue description

The system has detected an Electrically Erasable Programmable Read-Only Memory (EEPROM) error related to the number 4 electro-hydraulic remote (EHR) valve. The EEPROM stores calibration data and configuration settings for the valve. This error indicates that the memory data is corrupt, unreadable, or the memory chip itself has failed, which will likely cause the number 4 remote valve to become unresponsive or enter a failsafe mode.

Applies to these machines

  • Puma 125
  • Puma 130
  • Puma 140
  • Puma 145
  • Puma 150
  • Puma 160
  • Puma 165
  • Maxxum 110
  • Maxxum 115
  • Maxxum 120
  • Maxxum 125
  • Maxxum 145
  • Maxxum 150
  • Magnum 235
  • Magnum 245
  • Magnum 260
  • Magnum 290
  • Steiger Series
  • Quadtrac Series
  • Farmall 85U
  • Farmall 120U

Check the cause

  1. Inspect Wiring and Connectors: Carefully examine the wiring harness leading to the number 4 remote valve. Look for any signs of damage, such as chafing, corrosion, or loose connections, particularly in areas where the harness may flex or is exposed to the elements.

  2. Check for Other Fault Codes: Use the tractor's diagnostic menu or a diagnostic scanner to check for any other active or stored fault codes. Codes related to under-voltage (NH4146) or over-voltage (NH4147) on the same remote could indicate a power supply issue rather than a faulty EEPROM. Communication error codes may also point to a broader network issue.

  3. Clear Fault Codes and Recalibrate: Attempt to clear the fault codes from the system. After clearing the codes, perform a calibration of the EHR levers through the tractor's diagnostic menu. In some cases, a loss of calibration can trigger related faults.

  4. Software Update: In some instances, issues with EHR valves have been resolved with a software update from a Case IH dealer. It is worth checking if any software updates are available for the tractor's control modules.

Repair steps

  1. Acquire Replacement Valve

    Obtain the correct replacement electro-hydraulic control valve.

  2. Safety First

    Before starting any work, ensure the tractor is on a level surface, the parking brake is engaged, and the engine is off. It is also advisable to disconnect the battery.

  3. Access the Remote Valves

    The remote valve bank is typically located at the rear of the tractor. It may be necessary to remove covers or panels to gain access.

  4. Identify and Disconnect

    Identify the number 4 remote valve and disconnect the electrical connector.

  5. Remove Hydraulic Lines

    Carefully disconnect the hydraulic lines from the valve. Be prepared for some residual hydraulic fluid to leak out. It is good practice to label the lines to ensure correct reassembly.

  6. Remove the Valve

    Unbolt the faulty valve from the valve bank.

  7. Install the New Valve

    Mount the new electro-hydraulic control valve in place of the old one.

  8. Reconnect Hydraulic Lines and Electrical Connector

    Reconnect the hydraulic lines to the correct ports on the new valve and securely attach the electrical connector.

  9. Reconnect Battery and Clear Codes

    Reconnect the battery and use the tractor's diagnostic system to clear the NH4144 fault code.

  10. Calibrate the New Valve

    Perform the calibration procedure for the remote valve levers as specified for the tractor model. This is often done through the armrest display and involves moving the levers to their full extent to teach the system the new valve's parameters.

  11. Test Operation

    Start the tractor and test the functionality of the number 4 remote valve to ensure it is operating correctly.

Parts you might need

(4)
  • Common for Puma, Maxxum, and Farmall models.

  • Remanufactured electro-hydraulic control valve

    87546169R

    Remanufactured version of 87546169.

  • Kit for adding a 4th remote valve, includes the control valve.

  • Remote valve

    A169029

    Listed for 2nd, 3rd, or 4th remote valve on older Case and Case IH models.

Get help to fix this fault by requesting a quote

Browse other Case IH codes