Case IH TMF165 – TMF: PTO Shaft Rotation Detected Engine Off
Issue description
The Tractor Multi-Function (TMF) controller has detected rotation of the Power Take-Off (PTO) shaft while the engine is turned off. This typically indicates a false signal caused by a faulty PTO speed sensor, wiring harness damage, or signal misinterpretation by the controller, rather than actual unintended movement of the shaft.
Applies to these machines
38 machines- MX100C
- MX110
- MX120
- MX135
- MX180
- MX200
- MX210
- MX215
- MX220
- MX230
- MX240
- MX245
- MX255
- MX275
- MX285
- Magnum 215
- Magnum 235
- Magnum 275
- Magnum 280
- Magnum 290
- Magnum 305
- Magnum 310
- Magnum 315
- Magnum 335
- Magnum 340
- Puma 125
- Puma 140
- Puma 155
- Puma 165
- Puma 180
- Puma 195
- Puma 210
- Maxxum 110
- Maxxum 115
- Maxxum 120
- Maxxum 125
- Maxxum 130
- Maxxum 140
Check the cause
Retrieve all active and stored fault codes, particularly those related to the PTO, transmission, or electrical system
Visually inspect the wiring harness and connectors leading to the PTO speed sensor for chafing, corrosion, or loose connections
Check for moisture accumulation in unused connectors, specifically connector 146M of the rear axle harness on models with a dual-speed PTO
Verify the engine speed signal from the alternator's 'W' terminal, ensuring the alternator is charging correctly and the fan belt is properly tensioned
Check hydraulic and transmission fluid levels and condition, as low or contaminated fluid can cause general PTO malfunctions
Repair steps
Test PTO speed sensor
Disconnect the PTO speed sensor and measure resistance with a multimeter. Expected resistance is 2700-3300 Ohms. An open circuit (infinite resistance) or dead short (zero resistance) indicates a faulty sensor.
Test wiring harness
With the sensor disconnected and key off, check the signal wire for shorts to ground or power. There should be no continuity to the chassis and no voltage present with the key on and engine off.
Replace PTO speed sensor
If the sensor fails testing, replace it. Ensure the correct air gap between the sensor and tone wheel. Some technicians recommend using Teflon tape instead of an O-ring to allow slightly deeper threading for a better reading.
Clear codes and calibrate
Clear all fault codes from the TMF controller and operate the tractor to verify the fix. Perform a PTO calibration if required for your specific model.
Inspect TMF controller
If the fault persists after replacing the sensor and verifying wiring, inspect the TMF controller connectors for corrosion or damage. Consult a dealer technician with advanced diagnostic tools if the controller is suspected to be faulty.
Parts you might need
(12)- Rear PTO Shaft Speed Sensor87564763
Supersedes 82036589. Fits Maxxum (110-140), Puma (125-210), New Holland T6/T7.
- Dual PTO Speed Sensor87548197
Fits Magnum (215-340) and MX (180-285) series.
- PTO Speed Sensor47767004
Verify fitment by serial number.
- PTO Speed Sensor220119A1
Verify fitment by serial number.
PTO Solenoid Valve
Generic part, verify OEM number with dealer.
Tractor Multi-Function (TMF) Controller
Generic part, verify OEM number with dealer.
- PTO Speed Sensor84541361
Fits various Magnum, Puma, and Maxxum models.
- PTO Brake Band87391136
For reference only if mechanical failure is suspected
PTO Brake Band
87518135For reference only if mechanical failure is suspected
- PTO Brake Piston1289335C5
For reference only if mechanical failure is suspected
Get help to fix this fault by requesting a quote