776Bh

CLAAS 776Bh – ECM: Cylinder 6 Injector Ignition Inoperative

Issue description

The Engine Control Module (ECM) has detected a lack of combustion in cylinder 6, indicating an inefficient or absent ignition of the air-fuel mixture. This is typically caused by a failure in fuel delivery or the electrical signal to the cylinder 6 injector. The engine will experience difficulty running, misfires, loss of power, and an illuminated check engine light.

Applies to these machines

  • Lexion
  • Arion
  • Jaguar

Check the cause

  1. Use a diagnostic scanner to confirm the presence of the 776Bh code or related misfire codes (like P0306), and check for related fuel pressure or crankshaft sensor faults

  2. Visually inspect the wiring harness and electrical connector for the cylinder 6 fuel injector for damage, corrosion, or loose connections

  3. Listen for injector operation using a mechanic's stethoscope to ensure it makes a distinct clicking sound

  4. Use a multimeter to check the resistance of the injector coil against manufacturer specifications, and check for a pulsed voltage signal at the connector while running

  5. Swap the ignition coil (if applicable) or fuel injector between cylinder 6 and a known good cylinder (e.g., cylinder 5) to see if the fault code follows the component

  6. On spark ignition engines, use a spark tester to verify cylinder 6 is receiving spark

  7. Verify that fuel pressure is within the specified range to rule out a weak fuel pump or clogged filter

  8. Perform a compression test on cylinder 6 to check for mechanical engine issues (worn piston rings, faulty valves) if ignition and fuel systems are functioning correctly

Repair steps

  1. Safety preparation

    Ensure the engine is cool. Disconnect the negative battery terminal and relieve the pressure in the fuel system according to manufacturer instructions to prevent fuel spray.

  2. Access fuel rail

    Remove any engine covers, air intake tubes, or other components obstructing access to the fuel rail and injectors.

  3. Disconnect injector

    Disconnect the electrical connector from the fuel injector for cylinder 6.

  4. Remove fuel rail

    Unbolt the fuel rail from the intake manifold. Depending on the engine design, lift the entire rail with injectors attached or release individual clips holding each injector.

  5. Remove old injector

    Carefully pull the old injector out of its port on the fuel rail or intake manifold. Be prepared for residual fuel leakage.

  6. Install new injector

    Lubricate the new injector's O-rings with clean engine oil or gasoline to ensure a proper seal. Carefully press the new injector into place, ensuring it is properly seated.

  7. Reassemble components

    Reinstall the fuel rail and secure it with mounting bolts, torquing them to the manufacturer's specification. Reconnect the injector's electrical connector.

  8. Prime system and check for leaks

    Reinstall all removed covers. Reconnect the battery. Turn the ignition to the 'ON' position (without starting) for a few seconds to prime the fuel pump and build pressure. Inspect for fuel leaks.

  9. Test and clear codes

    Start the engine and check for smooth operation. Use a diagnostic scanner to clear the fault code and verify it does not return.

Parts you might need

(13)
  • Fuel Injector

    RE556741

    For some Claas Arion models with John Deere engines. Verify exact fitment by machine serial number and engine spec.

  • Fuel Injector0011505490

    For some Claas Arion models with John Deere engines. Verify exact fitment by machine serial number and engine spec.

  • Fuel Injector

    6005028965

    For various Claas/Renault models. Verify exact fitment by machine serial number and engine spec.

  • Fuel Injector

    RE507766

    For various Claas/Renault models. Verify exact fitment by machine serial number and engine spec.

  • Fuel Injector

    RE531436

    For various Claas/Renault models. Verify exact fitment by machine serial number and engine spec.

  • Fuel Injector6005021553

    For other Claas/Renault models. Verify exact fitment by machine serial number and engine spec.

  • Fuel Injector

    RE48786

    For other Claas/Renault models, and some John Deere engines used in Claas combines. Verify exact fitment by machine serial number and engine spec.

  • Fuel Injector

    RE44508

    For other Claas/Renault models. Verify exact fitment by machine serial number and engine spec.

  • Fuel Injector

    SE501139

    For some John Deere engines used in Claas combines. Verify exact fitment by machine serial number and engine spec.

  • Fuel Injector

    SE501135

    For some John Deere engines used in Claas combines. Verify exact fitment by machine serial number and engine spec.

  • Fuel Injector

    SE501123

    For some John Deere engines used in Claas combines. Verify exact fitment by machine serial number and engine spec.

  • Fuel Injector Seal Kit (O-rings)

    Highly recommended to replace whenever an injector is removed or replaced.

  • Injector Wiring Harness Connector

    Only needed if the original connector is damaged or corroded.

Get help to fix this fault by requesting a quote

Browse other CLAAS codes