Id787Bh / 787Bh

CLAAS Id787Bh / 787Bh – MFT (A30): Voltage delivered by the loudspeaker is too high

Issue description

The MFT (A30) Cebis terminal module has detected that the voltage delivered by the internal loudspeaker is too high. This electrical fault typically results in a continuous or inappropriate audible alarm being triggered by the system, indicating an abnormal voltage condition rather than a standard system alert.

Applies to these machines

  • CLAAS Axion 800 series (810, 820, 830, 840, 850)
  • CLAAS Axion 900 series (920, 930, 940, 950)
  • CLAAS Arion 500 and 600 series (e.g., 510-640)

Check the cause

  1. Inspect the loudspeaker (C22) of the Cebis terminal

  2. Verify the connections at the Cebis Terminal Module MFT (A30)

  3. Check the wiring harness between the MFT (A30) module and the C22 loudspeaker for any short-circuits to a power source or open circuits

  4. Check the internal resistance of the loudspeaker component to ensure it has not failed internally

Repair steps

  1. Power Down

    Turn off the tractor and disconnect the battery to prevent electrical spikes during testing.

  2. Access the Terminal

    Remove the necessary trim panels on the right-hand console to access the rear of the Cebis terminal (MFT A30) and the loudspeaker (C22).

  3. Inspect Wiring

    Visually inspect the wiring harness connecting the terminal to the loudspeaker. Look for chafed wires that might be shorting to a 12V source.

  4. Test the Loudspeaker

    Disconnect the loudspeaker and test it with a multimeter. If the resistance is out of specification or shorted, replace the loudspeaker.

  5. Test the Terminal Output

    If the wiring and loudspeaker are intact, the fault likely lies within the internal audio amplification circuitry of the Cebis terminal itself.

  6. Replace/Repair

    Replace the faulty component (either the C22 loudspeaker or the MFT A30 terminal). Note that Cebis terminals are often sent out for specialized remanufacturing if the internal board fails.

  7. Clear Codes

    Reconnect the battery, turn on the ignition, and clear the fault codes from the system memory.

Parts you might need

(8)
  • Cebis Terminal Module MFT (A30) / Cebis A030 Display

    2734522.0

    Fitment varies heavily by exact model year and whether it is an Axion or Arion; verify with dealer

  • Cebis Terminal Module MFT (A30) / Cebis A030 Display

    1810740.6

    Fitment varies heavily by exact model year and whether it is an Axion or Arion; verify with dealer

  • Cebis Terminal Module MFT (A30) / Cebis A030 Display

    00172600

    Fitment varies heavily by exact model year and whether it is an Axion or Arion; verify with dealer

  • Cebis Terminal Module MFT (A30) / Cebis A030 Display (Remanufactured)

    0015273.2

    For older Cebis II terminals

  • Cebis Terminal Loudspeaker (C22)

    J323 / C22

    Right console loudspeaker. If a part number cannot be sourced from the dealer, an equivalent impedance/wattage generic replacement speaker can often be spliced in.

  • CEBIS display speaker

    18130160

    OEM CLAAS replacement part

  • Mini Speaker

    668-1397-ND

    Digi-Key aftermarket alternative (28mm diameter, 8 ohm, 0.2W - 0.5W). Soldering or connectors may be required for installation.

  • Loudspeaker0000132543

    Generic CLAAS loudspeaker; compatibility with this specific CEBIS terminal is not confirmed.

Get help to fix this fault by requesting a quote

Browse other CLAAS codes