Deutz-Fahr 1022 – ECU: Actuator Fault AGR/Throttle Valve - Signal Range Exceeded
Issue description
The Engine Control Unit (ECU) has detected that the feedback signal from an actuator is out of the plausible range (signal range check high). The voltage received from the actuator's position sensor is above the maximum threshold defined in the ECU's programming. Depending on the engine model, this affects either the AGR/EGR valve or the throttle valve. This condition can be caused by an internal actuator failure, a short circuit to power in the wiring, or a mechanical issue causing the actuator to move past its normal range of motion.
Applies to these machines
6 machines- TCD 2.9 L4
- TCD 3.6 L4
- TCD 4.1 L4
- TCD 6.1 L6
- TCD 7.8 L6
- Genie boom lifts
Check the cause
Visually inspect the wiring harness and connectors leading to the actuator (EGR or throttle valve) for damage, corrosion, chafing, or loose connections.
Using a multimeter, check for proper supply voltage and ground at the actuator connector, and test the signal wire for a short circuit to a power source.
Measure the resistance of the actuator's internal circuits between the relevant pins to check for an internal electrical failure.
Use a diagnostic scan tool (e.g., Deutz SerDia) to monitor live data from the actuator's position sensor for consistently high or erratic signals.
Perform a bidirectional active test with the scan tool to command the actuator open and closed, verifying if it is mechanically stuck or failing to respond.
Inspect the AGR/EGR valve for heavy carbon buildup, or the throttle valve for obstructions that prevent free movement.
Repair steps
Safety First (All Models)
Ensure the engine is off and cool. Disconnect the battery.
Access the Valve (TCD 2.9 / 3.6 L4 Engines - AGR/EGR Valve)
Locate the EGR valve assembly. It is typically connected to the exhaust manifold and the intake system. Access may require removing other components or shields.
Disconnect (TCD 2.9 / 3.6 L4 Engines - AGR/EGR Valve)
Disconnect the electrical connector from the EGR actuator. Disconnect any coolant lines or exhaust pipes attached to the EGR cooler and valve. Be prepared to capture any draining coolant.
Remove the Valve (TCD 2.9 / 3.6 L4 Engines - AGR/EGR Valve)
Unbolt the EGR valve and cooler assembly from the engine.
Installation (TCD 2.9 / 3.6 L4 Engines - AGR/EGR Valve)
Install the new EGR valve assembly, ensuring all mounting surfaces are clean. Use new gaskets.
Reconnect (TCD 2.9 / 3.6 L4 Engines - AGR/EGR Valve)
Re-torque the bolts to the manufacturer's specification. Reconnect all pipes, coolant lines, and the electrical connector.
Final Steps (TCD 2.9 / 3.6 L4 Engines - AGR/EGR Valve)
Refill any lost coolant. Reconnect the battery. Clear the fault codes using a diagnostic tool and perform a test run to ensure the fault does not return.
Access the Valve (TCD 4.1 / 6.1 / 7.8 L Engines - Throttle Valve)
Locate the throttle valve on the air intake path, typically after the charge air cooler and before the intake manifold.
Disconnect (TCD 4.1 / 6.1 / 7.8 L Engines - Throttle Valve)
Disconnect the electrical connector from the throttle valve actuator. Remove the air intake hoses connected to the inlet and outlet of the throttle body.
Remove the Valve (TCD 4.1 / 6.1 / 7.8 L Engines - Throttle Valve)
Unbolt the throttle valve assembly from its mounting point.
Installation (TCD 4.1 / 6.1 / 7.8 L Engines - Throttle Valve)
Install the new throttle valve assembly, using a new gasket if required. Ensure the intake path is clean and free of debris.
Reconnect (TCD 4.1 / 6.1 / 7.8 L Engines - Throttle Valve)
Re-torque the mounting bolts to specification. Reconnect the air hoses and the electrical connector.
Final Steps (TCD 4.1 / 6.1 / 7.8 L Engines - Throttle Valve)
Reconnect the battery. Use a diagnostic tool to clear the fault code and perform any necessary adaptation or relearn procedure for the new throttle valve. Conduct a test run to verify the repair.
Parts you might need
(6)EGR Module Control Valve / EGR Valve
04133012OEM part for TCD 2.9 L4 & TCD 3.6 L4.
Aftermarket/Cross-Reference part for TCD 2.9 L4 & TCD 3.6 L4.
EGR Module Control Valve / EGR Valve
0412-0024Aftermarket/Cross-Reference part for TCD 2.9 L4 & TCD 3.6 L4.
EGR Module Control Valve / EGR Valve
0412-0424Aftermarket/Cross-Reference part for TCD 2.9 L4 & TCD 3.6 L4.
- Throttle Valve4124368
OEM part for TCD 4.1 L4, TCD 6.1 L6, TCD 7.8 L6.
Throttle Valve
12301550OEM part for TCD 4.1 L4, TCD 6.1 L6, TCD 7.8 L6.
Get help to fix this fault by requesting a quote