1757

Deutz-Fahr 1757 – ECU: AGR Actuator Current Above Limit

Issue description

The Exhaust Gas Recirculation (AGR/EGR) actuator is drawing an excessive amount of electrical current, surpassing the maximum specified threshold allowed by the system. This overcurrent condition typically indicates a short circuit in the actuator's motor windings, a short to ground in the wiring harness, or an internal failure of the actuator's electronic components. When active, this fault can cause rough idling, increased black exhaust smoke, reduced engine performance, increased fuel consumption, and the check engine light will be illuminated.

Applies to these machines

  • TCD 2.9
  • TCD 3.6
  • TCD 4.1
  • TCD 6.1
  • TCD 7.8
  • Genie GTH-844

Check the cause

  1. Use a diagnostic scan tool to check for any other active fault codes, particularly those related to battery voltage or other EGR sensors, which should be diagnosed first.

  2. Carefully inspect the EGR actuator's electrical connector and the surrounding wiring harness for damage, chafing, melting, corrosion, or oil/coolant contamination.

  3. Disconnect the EGR actuator and the ECU to check for a short circuit to ground in the power supply wire to the EGR actuator. Inspect pins in both connectors for damage, corrosion, or a loose fit.

  4. Manually attempt to move the EGR valve to ensure it moves freely without binding. Carbon buildup can cause the valve to stick, forcing the actuator motor to draw excessive current to overcome the resistance.

  5. Measure the resistance between the motor pins on the actuator. An extremely low reading indicates an internal short circuit within the actuator motor.

  6. Use a diagnostic tool like Deutz SerDia to command the EGR actuator open and closed. Monitor live data for commanded versus actual position and observe if the current draw spikes during operation.

Repair steps

  1. Disconnect battery

    Disconnect the negative battery cable before starting any electrical repairs to prevent short circuits or accidental starting.

  2. Drain coolant

    If the EGR system is liquid-cooled, partially drain the engine coolant to a level below the EGR valve to prevent spills when removing coolant lines.

  3. Remove access components

    Remove air intake pipes, heat shields, or other components as necessary to access the EGR actuator and valve assembly.

  4. Disconnect lines

    Carefully disconnect the electrical connector from the EGR actuator and disconnect any coolant lines from the EGR cooler/valve assembly.

  5. Remove EGR assembly

    Loosen and remove the mounting bolts securing the EGR assembly to the engine. Gentle prying may be necessary if the assembly is stuck due to carbon buildup.

  6. Clean mounting surfaces

    Thoroughly clean the gasket surfaces on the engine and intake manifold to ensure a proper seal with the new part.

  7. Install new EGR assembly

    Install the new EGR valve/actuator with a new gasket. Hand-tighten the bolts first, then torque them to the manufacturer's specifications in a crisscross pattern to ensure even pressure.

  8. Reconnect and refill

    Reconnect the electrical connector and any coolant lines. Refill the cooling system if it was drained.

  9. Clear codes and perform relearn

    Reconnect the battery. Use a diagnostic scan tool to clear the fault codes from the ECU. Perform an 'EGR actuator reset' or 'learn' procedure using a tool like Deutz SerDia to allow the ECU to calibrate and learn the end positions of the new actuator.

Parts you might need

(13)
  • Pierburg EGR Module

    7.05506.14.0

    For TCD 4.1 L4 engines

  • EGR Assembly with Cooler and Actuator

    04126486R

    For TCD 3.6L04 engines

  • For TCD 4.1 L4 engines (Alternative PN: M4510628)

  • For TCD 4.1 L4 engines (Alternative PN: D4510627)

  • EGR Valve / EGR Actuator / EGR Module

    04120024

    Verify fitment with engine serial number.

  • Verify fitment with engine serial number.

  • EGR Valve / EGR Actuator / EGR Module

    04120424

    Specifically listed as 24V.

  • Specifically listed as 24V.

  • Specifically listed as 12V.

  • EGR Valve / EGR Actuator / EGR Module

    M4510628
  • EGR Valve / EGR Actuator / EGR Module

    04133012

    Verify fitment with engine serial number.

  • Verify fitment with engine serial number.

  • EGR Valve / EGR Actuator / EGR Module

    M4120822

    Verify fitment with engine serial number.

Get help to fix this fault by requesting a quote

Browse other Deutz-Fahr codes