Deutz-Fahr 190 – ECU: Speed Signals of Crank-shaft and Cam-shaft Are Phase-Shifted
Issue description
Fault code 190, often displayed with an associated DEUTZ error code 78 and SPN 190, signifies that the signals from the crankshaft and camshaft position sensors are out of phase. The Engine Control Unit (ECU) continuously compares the timing of these two signals to monitor the engine's rotational position and ensure correct injection and valve timing. When the expected synchronization is lost, the ECU flags this fault. The system reaction to this fault is often a warning light on the dashboard and, critically, it may prevent the engine from starting as a protective measure.
Applies to these machines
6 machines- DEUTZ TCD 2012 Series
- DEUTZ TCD 2013 Series
- DEUTZ TCD 2015 Series
- DEUTZ BF4M 1013 Series
- DEUTZ BF6M 1013 Series
- General DEUTZ engines using EMR3, EMR4, and KF series controls
Check the cause
Verify the fault code presence (SPN 190 with FMI 2, 8, 11, or 12) using a diagnostic tool like DEUTZ SerDia. The blink code associated with this fault is typically 2-1-3.
Visually inspect the wiring harnesses for both the crankshaft and camshaft sensors for signs of damage, chafing, corrosion, or loose pins.
Check sensor wiring and polarity to ensure it matches the manufacturer's schematic.
Inspect the mounting of both sensors to ensure they are secure and check the air gap between the sensor and the reluctor wheel.
Visually inspect the crankshaft and camshaft sensor wheels (reluctor wheels) for bent or missing teeth, and confirm they have not slipped or become misaligned.
Test sensor functionality using an oscilloscope to verify the signal output waveforms are clean, consistent, and correctly timed relative to each other.
If two identical sensors are used, swap their positions to determine if the fault behavior changes, which would point to a defective sensor.
Repair steps
Disconnect Power
Turn the ignition off and disconnect the battery to prevent electrical damage.
Access Sensors
Locate the crankshaft and camshaft position sensors on the engine. Their location varies by engine model but the crankshaft sensor is typically near the flywheel housing, while the camshaft sensor is often on the timing case or cylinder head cover.
Perform Diagnostics
Follow the diagnostic checks listed in the section above to identify the root cause (wiring, alignment, or faulty sensor).
Repair/Replace as Needed
Wiring: If wiring is damaged, repair or replace the affected section of the harness. Ensure connectors are clean and secure. Sensor Wheel: If a sensor wheel is damaged or misaligned, it must be correctly positioned or replaced (potentially requiring removal of the timing cover or other major engine components). Sensor Replacement: If a sensor is identified as faulty, unscrew the mounting bolt, remove the old sensor, and install the new one. Ensure it is seated correctly and the air gap is set to specification if adjustable.
Clear Fault Codes
Reconnect the battery and turn on the ignition. Use a diagnostic tool to clear the stored fault codes from the EMR3 ECU.
Verify Repair
Start the engine and let it run. Re-scan for fault codes to ensure the issue is resolved. The warning lamp should remain off.
Parts you might need
(7)- Crankshaft Speed Sensor04199447
Fits various Deutz engines including TCD 2012, TCD 2013, TCD 2015, and BF1013 series.
- Crankshaft Speed Sensor4199447
Fits various Deutz engines including TCD 2012, TCD 2013, TCD 2015, and BF1013 series.
Crankshaft Speed Sensor
04203060Fits various Deutz engines including TCD 2012, TCD 2013, TCD 2015, and BF1013 series.
- Crankshaft Speed Sensor04213840
May serve as both a crank and cam sensor on some models like the TD2.9 and TD3.6.
- Camshaft Speed Sensor04214103
Fits various Deutz engines including TCD 2012 and TCD 2013 series.
- Camshaft Speed Sensor04210924
Fits various Deutz engines including TCD 2012 and TCD 2013 series.
Camshaft Speed Sensor
04213578Fits various Deutz engines including TCD 2012 and TCD 2013 series.
Get help to fix this fault by requesting a quote