571

Deutz-Fahr 571 – ECU: Injector 4 in Firing Order: Power Interruption

Issue description

The Engine Control Module (ECM) has detected that the electrical current to the injector solenoid for cylinder #4 (in the firing order) is below the normal range, or that there is an open circuit. When the ECM attempts to actuate the injector, it does not detect the expected rise in current, indicating a break in the electrical connection. This power interruption can result in improper engine performance, rough idle, misfire, reduced engine power, an illuminated amber 'CHECK ENGINE' light, and possible white smoke from the exhaust due to unburned fuel.

Applies to these machines

  • TCD 4.1 L4
  • TCD 6.1 L6
  • TCD 3.6 L4
  • TCD 2.9 L4
  • TCD 2013
  • TCD 2013 L6 2V
  • TCD 2015
  • TCD4L2012
  • TCD6L2012

Check the cause

  1. Visually inspect the wiring harness leading to injector 4 for chafing, breaks, or heat damage.

  2. Check the injector's electrical connector for corrosion, loose pins, or oil/fuel contamination (oil intrusion into connectors is a common cause).

  3. Perform a continuity test using a multimeter from the ECM to the injector connector to identify any open circuits in the wiring harness.

  4. Disconnect the injector's electrical connector and measure the resistance across the two terminals of the injector itself. An infinite reading indicates an open circuit within the injector coil. Compare the reading to the other injectors; it should be within a similar range.

  5. Swap the suspect injector (injector 4) with an adjacent one (e.g., injector 3), clear codes, and run the engine. If the fault follows the injector, the injector is faulty. If code 571 returns, the issue lies in the wiring or ECM.

  6. Use a diagnostic scan tool to perform an injector cut-out test to confirm cylinder 4 is not contributing, and monitor the current to the injector during operation.

Repair steps

  1. Access the injector

    Remove any components obstructing access to the fuel injectors, such as the cylinder head cover or intake pipes.

  2. Disconnect fuel lines

    Thoroughly clean the area around the injector. Disconnect the high-pressure fuel line and the fuel return line from the injector. Be prepared to catch any residual fuel with rags.

  3. Disconnect electrical connector

    Unplug the electrical harness from the injector.

  4. Remove the injector

    Loosen and remove the bolt(s) for the injector hold-down clamp. If the injector is seized in the cylinder head, a specialized injector removal tool or slide hammer may be required.

  5. Install the new injector

    Ensure the injector bore in the cylinder head is perfectly clean. Apply a thin coat of anti-seize compound to the threads of the new injector. Install the new injector and its clamp. Tighten the hold-down bolt to the manufacturer's specified torque (e.g., for a TCD 4.1 L4 engine, the torque for the cable connection on the injector is 1.5 Nm; verify main hold-down torque in a service manual).

  6. Reconnect lines

    Reconnect the high-pressure fuel line and the return line. Use new sealing rings where applicable.

  7. Final assembly

    Reconnect the electrical connector and reinstall any covers or components that were removed.

  8. Bleed the fuel system

    Bleed air from the fuel lines before attempting to start the engine.

  9. Test and verify

    Start the engine and check for any fuel leaks around the newly installed injector. Use a diagnostic tool to clear the fault codes and confirm that fault 571 does not reappear.

Parts you might need

(8)
  • Fuel Injector (TCD 4.1 L4 & TCD 6.1 L6)

    04504664

    Alternate part number 4514650. Verify correct part number with dealer using machine serial number.

  • Fuel Injector (TCD 3.6 L4)

    04123831

    Verify correct part number with dealer using machine serial number.

  • Fuel Injector (TCD 2.9 L4)

    04132014

    Bosch cross-reference: 0 445 110 561. Verify correct part number with dealer using machine serial number.

  • Fuel Injector (TCD 2013 L6 2V)

    04290986

    Verify correct part number with dealer using machine serial number.

  • Alternate part number 04290987. Verify correct part number with dealer using machine serial number.

  • Deutz OEM part number. Verify correct part number by engine model and serial number. Inspect fuel system for contamination and replace fuel filter when replacing.

  • Common Rail Fuel Injector (Bosch)

    0445120067

    Bosch OEM part number. Verify correct part number by engine model and serial number. Inspect fuel system for contamination and replace fuel filter when replacing.

  • Common Rail Fuel Injector (Volvo)

    20798683

    Volvo cross-reference part number. Verify correct part number by engine model and serial number. Inspect fuel system for contamination and replace fuel filter when replacing.

Get help to fix this fault by requesting a quote

Browse other Deutz-Fahr codes