573

Deutz-Fahr 573 – ECU: EGR Valve Position Voltage Low

Issue description

The Engine Control Unit (ECU) has detected that the voltage from the Exhaust Gas Recirculation (EGR) valve's position sensor is below the normal operating range or has short-circuited to ground. This loss of accurate position feedback prevents the ECU from properly controlling the amount of exhaust gas recirculated into the intake manifold, which can lead to rough idling, stalling, reduced fuel economy, sluggish acceleration, and increased emissions.

Applies to these machines

  • Deutz TCD 2.9L
  • Deutz TCD 3.6L
  • Deutz FARMotion
  • 5D VSF CVT (T4i) Series

Check the cause

  1. Confirm the fault code (SPN 27, FMI 4) is active or has a high occurrence count using a diagnostic scanner like Deutz SerDia.

  2. Inspect the EGR valve's electrical connector and wiring harness for damage, corrosion, moisture, or loose pins.

  3. Perform a wiggle test on the connector and wiring harness while monitoring live EGR position sensor voltage for sudden drops.

  4. Check for a short to ground by disconnecting the EGR valve and ECU connectors and measuring resistance between the signal and ground pins (specifically check pin A36 on 5D T4i series).

  5. Verify sensor voltage using a multimeter: check for a 5-volt supply, ground, and signal wire. The signal should be ~0.9V when closed; a drop below 0.3V triggers the fault.

  6. Command the EGR valve to open and close using a diagnostic tool to see if the sensor's position feedback matches the commanded position. If it does not, the valve assembly has likely failed internally.

Repair steps

  1. Prepare machine

    Ensure the engine is completely cool and disconnect the negative battery terminal to prevent electrical issues.

  2. Drain coolant

    If the EGR valve is integrated with the cooling system, place a drain pan underneath and drain the necessary amount of coolant before disconnecting hoses.

  3. Disconnect valve components

    Unplug the electrical connector from the EGR valve and disconnect any vacuum or coolant hoses using pliers to release the clamps.

  4. Remove EGR valve

    Remove the mounting bolts securing the EGR valve to the engine or cooler (use penetrating oil if stubborn). Gently detach the old valve and carefully scrape away the old gasket material with a plastic scraper.

  5. Install new EGR valve

    Place a new gasket on the clean mounting surface, position the new EGR valve, and hand-thread the mounting bolts to prevent cross-threading.

  6. Torque bolts

    Tighten the mounting bolts in a crisscross or star pattern to the manufacturer's specified torque value. Do not overtighten.

  7. Reconnect and refill

    Reconnect the electrical connector and all hoses. Refill the coolant system to the proper level if it was drained.

  8. Calibrate and test

    Reconnect the battery, clear fault codes with a diagnostic tool, perform an EGR relearn or calibration procedure via the ECU, and road test the machine to ensure the fault does not return.

Parts you might need

(6)
  • EGR Valve

    04120412

    Listed for Deutz TCD 2.9L and TCD 3.6L engines

  • EGR Control Valve

    04120012

    Referenced as a control valve for Deutz TCD 3.6L engines

  • EGR Valve

    04120024

    Replacement EGR valve for Deutz TCD 2.9L and TCD 3.6L engines (also listed as 04120424)

  • EGR Control Valve

    04134412

    Listed for D / TD / TCD 2.9 L4 engines

  • EGR Valve04906915

    Noted to fit some Deutz-Fahr and SAME tractors

  • EGR Module

    04133060

    Listed for Deutz applications

Get help to fix this fault by requesting a quote

Browse other Deutz-Fahr codes