Deutz-Fahr 795 – ECM: EGR Differential Pressure Sensor Signal Low
Issue description
The Engine Control Unit (ECU) has detected an abnormally low voltage signal from the Exhaust Gas Recirculation (EGR) differential pressure sensor (corresponding to SPN 411, FMI 3). This sensor measures the pressure difference of the exhaust gas before and after it passes through the EGR venturi, allowing the ECU to regulate exhaust gas flow. A signal range check low typically indicates an open circuit, a short to ground, or an internal failure of the sensor itself. When this fault is active, the ECU will likely disable EGR valve actuation as a protective measure.
Applies to these machines
45 machines- Deutz TCD 2.9
- Deutz TCD 3.6
- Deutz TCD 4.1
- Deutz TCD 6.1
- Deutz TCD 7.8
- Agrofarm 85
- Agrofarm 100
- Agrofarm 420
- Agrofarm 430
- Agroplus 85
- Agroplus 100
- Agrotron K Series (K100 - K610)
- Agrotron MK3 Series
- Agrotron 6120
- Agrotron 6130
- Agrotron 6140
- Agrotron 6145.4
- Agrotron 6155
- Agrotron 6155.4
- Agrotron 6165
- Agrotron 6165.4
- Agrotron 6175
- Agrotron 6175.4
- Agrotron 6185
- Agrotron 6205
- Agrotron 6215
- Agrotron TTV 6120
- Agrotron TTV 6130
- Agrotron TTV 6140
- Agrotron TTV 6155
- Agrotron TTV 6155.4
- Agrotron TTV 6165
- Agrotron TTV 6165.4
- Agrotron TTV 6175
- Agrotron TTV 6175.4
- Agrotron TTV 6185
- Agrotron TTV 6205
- Agrotron TTV 6215
- Agrotron TTV 7230
- Agrotron TTV 7250
- Agrotron TTV 8280
- Agrotron TTV 9270
- Agrotron TTV 9290
- Agrotron TTV 9310
- Agrotron TTV 9340
Check the cause
Inspect the EGR system, venturi unit, and associated pipework for any signs of damage, leaks, or loose connections
Check the venturi bores and the pipes leading to the differential pressure sensor for soot blockages or carbon buildup
Inspect the sensor wiring harness for chafing, breaks, or corrosion, and ensure the connector is securely attached
Test the sensor electrical connection for a stable 5V power supply and a good ground
Measure the sensor signal voltage with the ignition on (engine off) to confirm if the reading is near zero
Check the EGR valve to ensure it is not stuck closed, which could prevent pressure changes from being detected
Repair steps
Prepare machine
Stop the engine and allow it to cool. Disconnect the battery before working on the electrical system.
Access the sensor
Locate the EGR differential pressure sensor, which is typically mounted near the EGR valve and venturi housing and connected by two small hoses.
Inspect and clean
Disconnect the hoses and electrical connector from the sensor. Inspect the hose ports on both the sensor and the venturi unit for soot blockages. Clean the ports and hoses thoroughly.
Replace the sensor
If cleaning the ports and hoses does not resolve the issue, the sensor is likely faulty. Replace the differential pressure sensor with a new part.
Reassemble and clear codes
Securely reconnect the hoses and electrical connector to the sensor. Reconnect the battery and use a diagnostic tool to clear the stored fault codes from the EMR4 engine controller.
Verify the repair
Start the engine and check for any pending or active fault codes. Perform a test drive under various load conditions to confirm the EGR system is operating correctly.
Parts you might need
(3)- EGR Differential Pressure Sensor04211682
Most common part number for this sensor across various Deutz engines and Deutz-Fahr models. Also listed as 4211682.
- EGR Differential Pressure Sensor04213504
Alternative part number for Deutz TCD engines.
- Pressure Sensor4216643
Alternative part number for Deutz TCD engines.
Get help to fix this fault by requesting a quote