927

Deutz-Fahr 927 – ECM: DEF Temperature Measurement Failure

Issue description

The Engine Control Unit (ECU) requested a temperature measurement from the AdBlue (DEF) supply module, but the measurement is not available or is implausible. This indicates a failure in the temperature measurement process for the AdBlue supply module. The SCR system relies on this temperature reading to prevent the diesel exhaust fluid from freezing (around -11°C or 12°F) and to ensure it does not overheat and degrade. If the ECU cannot determine the temperature, it will flag this fault and may enter a derate or limp mode to prevent damage to the aftertreatment system and maintain emissions compliance.

Applies to these machines

  • Agrotron

Check the cause

  1. Trace the wiring harness from the DEF tank header assembly to the ECM. Look for any signs of chafing, melting near exhaust components, pinch points, or rodent damage.

  2. Disconnect the main electrical connector at the DEF tank. Inspect the pins for corrosion (often green or white), moisture, or physical damage like bent or pushed-out pins.

  3. With the key on, use a multimeter to verify that the sensor connector is receiving the correct voltage and has a solid ground connection according to the wiring diagram.

  4. Measure the resistance across the temperature sensor's pins on the header assembly connector. Compare to specs (e.g., ~942 Ohms at 0°C, ~608 Ohms at 10°C, ~330 Ohms at 25°C, ~189 Ohms at 40°C). Zero ohms indicates a short circuit, while infinite resistance (OL) indicates an open circuit.

  5. Disconnect the harness from both the sensor and the ECM. Check for continuity on each wire to rule out a break, and check for shorts between wires and to ground.

  6. Use a diagnostic scan tool to read live data from the DEF temperature sensor. If the reading is stuck at an extreme value (e.g., -40°C or a very high temperature) or does not change as the system warms up, it strongly suggests a sensor or wiring fault.

Repair steps

  1. Confirm the Fault

    Read the active fault codes with a compatible diagnostic scanner to confirm that code 927 (or its SPN/FMI equivalent) is present.

  2. Perform Diagnostic Checks

    Follow the diagnostic steps outlined above to isolate the root cause.

  3. Repair Wiring/Connectors

    If visual inspection or electrical tests reveal damaged wiring or corroded connectors, repair or replace the affected sections of the harness. Clean any corroded pins with electrical contact cleaner and ensure a secure connection. Clear codes and re-test.

  4. Replace the DEF Header Assembly

    If the wiring and connections are confirmed to be good, the fault lies within the DEF temperature sensor itself. Since the sensor is typically integrated into the DEF tank header unit, the entire assembly must be replaced.

  5. Clear Fault Codes and Perform System Test

    After replacing the component, use a scan tool to clear all fault codes from the ECM. Start the engine and let it run to allow the SCR system to perform a self-test. Monitor the live data to ensure the new DEF temperature sensor is reading correctly.

Parts you might need

(10)
  • DEF Tank Header Assembly

    04606710

    Also known as DTZ4606710. Fits Deutz.

  • Deutz Ad-Blue Tank Level Sensor

  • Genuine Deutz Header Def Tank 10L

  • Ad Blue Tank Assembly

    04606111

    Deutz Ad Blue Tank Assembly

  • DEF Head Unit

    5100078973

    Wacker Neuson part number for a Deutz DEF Head Unit

  • AdBlue/DEF Temperature Sensor

    04210898

    OEM Deutz Temperature Sensor. Verify application by serial number.

  • AdBlue/DEF Temperature Sensor

    04217846

    Temperature sensor for various Deutz 2011 series engines. Verify application.

  • For various Deutz 2011 series engines. Verify application.

  • For various Deutz engines. Verify application.

  • Verify application.

Get help to fix this fault by requesting a quote

Browse other Deutz-Fahr codes