P0340-64

Deutz-Fahr P0340-64 – Engine Control Unit (ECU) / EMR3 / EMR4: Camshaft Position Plausibility Error

Issue description

The system has detected a plausibility error related to the camshaft position. This indicates that the measured camshaft position signal received by the Engine Control Unit (ECU) does not match expected values or behavior, specifically being out of sync with the crankshaft position sensor. Rather than a simple missing signal, this mismatch suggests a potential mechanical timing issue, an electrical fault in the circuit, or a failing component responsible for monitoring the camshaft position.

Applies to these machines

  • Deutz TCD 3.6 L4
  • Deutz TCD 2012
  • Deutz TCD 2013

Check the cause

  1. Check for other active or stored fault codes using a diagnostic scanner (e.g., P0335 for crankshaft sensor or P0016 for timing correlation) to provide diagnostic context

  2. Visually inspect the wiring harness and connector for the camshaft position sensor for signs of damage such as chafing, rubbing against other components, heat damage, cracked insulation, or corrosion in the connector pins

  3. Ensure the sensor connector is clean, free of oil or moisture, and securely fastened

  4. Identify if the sensor is a 2-wire (magnetic/variable reluctance) or 3-wire (Hall-effect) type to determine the correct electrical test

  5. For 3-wire Hall-effect sensors: Turn the ignition to the 'ON' position (engine off). Check for reference voltage (typically 5V or 12V) at the power wire, verify a good ground connection, and back-probe the signal wire while cranking to check for a fluctuating DC voltage or a square wave if using an oscilloscope

  6. For 2-wire magnetic sensors: With the ignition off and the sensor disconnected, measure internal resistance across the two sensor pins (typically 200-1,000 ohms). Set the multimeter to AC voltage and measure for a fluctuating AC voltage output from the sensor while cranking the engine

  7. Inspect the engine's mechanical timing components (timing belt, chain, and gears) for excessive wear, slack, damage, or a jumped tooth

  8. Check the sensor tone wheel (reluctor) for damage, looseness, or missing teeth

Repair steps

  1. Perform Diagnostics

    Complete the electrical and mechanical diagnostic checks to isolate the root cause. Do not replace the sensor unless tests confirm it has failed.

  2. Address Wiring/Connector Issues

    If any wiring or connector faults are found, repair or replace the damaged section of the harness or the connector itself. Clear the fault codes and re-test.

  3. Replace the Camshaft Position Sensor

    If the sensor is confirmed faulty: Disconnect the negative battery terminal. Locate the sensor (on the camshaft housing for TCD 3.6 L4 engines) and disconnect the electrical connector. Remove the single mounting bolt (typically 8mm or 10mm). Gently twist and pull the old sensor out of its bore. Ensure the old O-ring has been removed. Clean the sensor mounting surface. Lightly lubricate the new O-ring with clean engine oil and install it on the new sensor. Install the new sensor and tighten the mounting bolt to the manufacturer's specified torque. Do not overtighten. Reconnect the electrical connector and the battery terminal.

  4. Clear Codes and Verify Repair

    Use a diagnostic tool to clear the P0340-64 fault code. Start the engine and let it run to ensure the code does not return. Perform a test drive under normal operating conditions.

Parts you might need

(3)
  • DEUTZ CORP / Memo (Aftermarket). Listed for Deutz TCD 2012 and TCD 2013 engines. Verify fitment by serial number.

  • Cross-references to D4213840. Listed for Deutz 2013, 2015, TD3.6, and TCD 2.9 engines. Verify fitment by serial number.

  • Cross-references to D4199447. Listed for various Deutz series including TCD 2.9 L4 and TCD 3.6 L4. Verify fitment by serial number.

Get help to fix this fault by requesting a quote

Browse other Deutz-Fahr codes