A001

Fendt A001: Unit Emergency Mode During CAN-Bus Transmission Testing

Issue description

The system has entered emergency mode during a test of the CAN-Bus transmission, indicating a breakdown in communication between electronic control units (ECUs) on the tractor's network. This general bus failure causes the affected system (such as the PTO, 4WD, or transmission) to lose function and enter a limp mode to prevent damage. This code acts as a prefix and is typically accompanied by a secondary code identifying the specific module experiencing the communication loss.

Applies to these machines

  • Farmer 400 Series
  • Favorit 700 Series
  • Favorit 900 Series
  • 300 Vario COM III
  • 700 Vario COM III
  • 800 Vario COM III
  • 900 Vario COM III
  • 409 Vario
  • 410 Vario
  • 411 Vario
  • 412 Vario
  • 828 Vario
  • 933 Vario
  • 939 Vario

Check the cause

  1. Record all active and stored fault codes to identify the specific module accompanying the A001 prefix

  2. Check fuses F040 and F041 on the A013 printed circuit board (PCB), located inside the cab and accessible by removing a side cover, for the CAN bus power supply

  3. Visually inspect wiring harnesses connected to the faulting control module for damage, corrosion, loose connections, or rubbing against the chassis

  4. Perform a CAN bus resistance check with the ignition off (measure between CAN-High and CAN-Low; expected is approximately 60 Ohms. 120 Ohms indicates an open circuit or faulty terminating resistor, while significantly lower indicates a short circuit)

  5. Check for shorts to power or ground on the CAN lines with the ignition on (expected voltage is typically around 2.5V, with CAN-High slightly above and CAN-Low slightly below. Readings close to battery voltage or 0V indicate a short to power or ground)

Repair steps

  1. Address fuse issues

    If fuses F040 or F041 are blown, replace them with fuses of the correct amperage. If a new fuse blows immediately, trace and repair the short circuit in the power supply.

  2. Repair damaged wiring

    Repair or replace any damaged wiring or corroded connectors found during the visual inspection. Ensure all connections are clean and secure.

  3. Isolate faulty module (for short circuits)

    If a short circuit is detected on the CAN bus, unplug control modules one by one. When the faulty module is disconnected, the CAN bus resistance or voltage readings will return to normal.

  4. Address open circuits

    If an open circuit is suspected (e.g., a 120 Ohm resistance reading), check the wiring, connectors, and terminating resistors between the control modules.

  5. Replace faulty component

    If a specific control module is identified as faulty, replace it. Note that this may require programming or calibration with Fendt's diagnostic software (FENDIAS).

  6. Clear codes and test

    After repairs, clear all fault codes from the system. Operate the tractor and the affected function to ensure the fault does not return.

Parts you might need

(9)
  • New, for various models

  • Vario Transmission Controller

    G737.100.970.011

    For 300 Com3 series

  • Vario Transmission Controller

    Z931100970013

    Verify fitment by serial number

  • PTO Control Unit (Remanufactured)

    G395.970.100.045

    For Farmer series

  • PTO Command Switch

    680085

    Verify fitment by serial number

  • Verify fitment by serial number

  • PTO Switch with LEDG312970090011

    For 300/400/Favorit series

  • Transmission Speed Sensor

    G350100970011

    Verify fitment by serial number

  • Automotive blade fuses

    Standard fuses of the correct amperage for F040 and F041

Get help to fix this fault by requesting a quote

Browse other Fendt codes