P0003

JCB P0003 – ECM: IMV Driver Fault Detected

Issue description

The Engine Control Module (ECM) has detected a low voltage condition in the control circuit for the Inlet Metering Valve (IMV), also known as the Fuel Volume Regulator. The IMV is a solenoid valve mounted on the high-pressure fuel pump that regulates fuel pressure in the common rail. A low voltage signal indicates a potential short to ground, open circuit, high resistance in the wiring, a faulty valve, or an internal ECM issue. This fault can cause the system to enter limp mode, resulting in reduced engine power, difficulty starting, or engine stalling.

Applies to these machines

  • Ecomax Tier 4
  • Ecomax Tier 4i
  • Tier 2 Electronic Engine
  • Tier 3 Electronic Engine
  • 444 Engine
  • 448 Engine
  • 510-56 Loadall
  • 531 Loadall
  • 535 Loadall
  • 3CX Backhoe
  • 4CX Backhoe

Check the cause

  1. Retrieve all fault codes using a diagnostic scan tool to check for related fuel pressure, sensor, or ECM faults

  2. Inspect fuses and relays related to the engine control and fuel system circuits

  3. Visually inspect the wiring harness and connectors between the ECM and the IMV for corrosion, damage, fraying, or rubbing against engine components

  4. With ignition on and engine off, disconnect the IMV connector and measure voltage at the supply wire to ensure proper reference voltage (e.g., 5V or 12V)

  5. Verify the ground wire in the IMV connector has good continuity to the chassis ground

  6. Measure the resistance across the two terminals of the IMV and compare to manufacturer specifications to check for an open or shorted valve

  7. Perform JCB-specific diagnostic tests using the Servicemaster tool, such as the IMV Override Test, Static Test, or Dynamic Test

Repair steps

  1. Safety First

    Ensure the machine is on level ground, safely parked, and the engine is off and cool. Disconnect the battery.

  2. Relieve Fuel Pressure

    Follow the manufacturer's procedure to safely relieve any residual pressure in the fuel system.

  3. Locate the IMV

    The Inlet Metering Valve is located on the high-pressure fuel pump.

  4. Remove the Old Valve

    Disconnect the electrical connector. Clean the area around the valve to prevent contamination of the fuel system. Remove the retaining bolts and carefully extract the valve from the pump body.

  5. Install the New Valve

    Ensure the new valve is the correct part for the application. Lubricate the O-rings with clean diesel fuel or a suitable assembly lubricant. Carefully insert the new valve into the pump and tighten the retaining bolts to the manufacturer's specified torque.

  6. Reconnect and Reassemble

    Reconnect the electrical connector. Re-install any other components that were removed for access.

  7. Prime the Fuel System

    Reconnect the battery. Follow the JCB-specific procedure to prime the fuel system to remove any air introduced during the repair. This may involve using the priming pump or running a specific function with a diagnostic tool.

  8. Final Verification

    Start the engine and check for any fuel leaks. Allow the engine to reach operating temperature. Use a scan tool to clear the P0003 fault code and verify that it does not return.

Parts you might need

(5)
  • Always verify fitment by serial number.

  • Inlet Metering Valve (IMV) - Delphi

    9109-936A

    Primary Delphi part number.

  • Inlet Metering Valve (IMV) - Delphi Alternative

    28233373

    Often cross-references with 9109-936A.

  • May be an older or alternative number.

  • Inlet Metering Valve (IMV) - Delphi Alternative

    9307Z532A

    Listed for JCB applications.

Get help to fix this fault by requesting a quote

Browse other JCB codes