P0264

JCB P0264 – ECU / PCM: Injector Circuit Low Cylinder 2

Issue description

The Engine Control Unit (ECU) has detected a low voltage or insufficient current in the electrical circuit for the fuel injector of the second cylinder. The ECU controls the fuel injectors by providing a pulsed ground signal and expects to see a specific voltage range in the circuit. When the voltage drops below a predetermined threshold, the ECU registers this fault. This condition compromises precise fuel delivery to cylinder 2, leading to improper engine operation and performance issues.

Applies to these machines

  • 3CX Backhoe Loader
  • 4CX Backhoe Loader
  • JCB Telehandlers
  • JCB 444 Engine
  • JCB Ecomax 444 Engine
  • JCB Dieselmax Engine
  • Other equipment utilizing Tier 3 and Tier 4 JCB engines

Check the cause

  1. Ensure the engine is stopped and allowed to cool before beginning any work.

  2. Inspect the wiring harness leading to the number 2 fuel injector for signs of damage, chafing, cuts, or heat damage from hot engine components. Note that on JCB engines, harness routing can sometimes lead to rubbing and intermittent open circuits.

  3. Check the electrical connector at the number 2 injector and the ECU pins for a secure fit, corrosion, moisture, or debris, which can result from pressure washing or a poor seal.

  4. Disconnect the cylinder 2 fuel injector and use a multimeter to measure the resistance across its terminals, comparing the reading to manufacturer specifications.

  5. With the ignition on and engine off, use a multimeter to check for proper supply voltage (typically 5V or 12V) at the injector connector's supply wire.

  6. Plug a noid light into the injector connector and crank the engine to verify the ECU is sending the pulse signal (a flashing light indicates a good signal; off or dim indicates a wiring or ECU driver issue).

  7. Swap the suspect injector from cylinder 2 with an injector from another cylinder (e.g., cylinder 1 or 3), clear codes, and run the engine to see if the fault code follows the injector or stays on cylinder 2.

Repair steps

  1. Address connection issues

    If the visual inspection revealed a loose or corroded connector, clean the terminals with contact cleaner and ensure the connector is securely reseated. Carefully tighten any loose pins within the connector to ensure a snug fit on the injector posts.

  2. Repair wiring

    If the wiring harness is damaged, repair the affected wires by properly soldering and insulating them with heat-shrink tubing. Secure the harness away from sharp edges or heat sources to prevent future damage.

  3. Replace the fuel injector

    If diagnostic tests or component swapping confirm the fuel injector is faulty, replace it. It is recommended to replace the entire set of injectors on higher-hour machines or when using aftermarket parts to ensure consistent fuel delivery and atomization.

  4. Repair or replace ECU

    If all wiring, connections, and injectors are functioning properly, the fault may lie with the injector driver within the ECU. Send the ECU to a specialist for testing and repair, or replace it (a replacement ECU will require programming to the specific machine).

Parts you might need

(9)
  • Fuel Injector320/06834

    Fits some JCB 444 NA Range engines, commonly found in 3CX and 4CX Backhoe Loaders

  • Fuel Injector

    320/06881

    Fits some Tier 4 JCB 444 engines

  • Fuel Injector320/06838

    Fits some JCB 444 Tier 3 engines in 3CX and 4CX Loaders

  • Fuel Injector

    320/06839

    Fits some JCB 444 Tier 3 engines in 3CX and 4CX Backhoe Loaders

  • Fuel Injector320/06529

    Fits some JCB Dieselmax engines in 3CX and 4CX Backhoe Loaders

  • Fuel Injector

    17/105400

    Fits some JCB loaders (3CX, 4CX) equipped with Perkins 1004 engines

  • Fuel Injector

    320/06724

    Mentioned for JCB 3CX and 4CX models

  • Fuel Injector

    320/06694

    Mentioned for JCB 3CX and 4CX models

  • Fuel Injector

    228260864

    Fits some JCB Ecomax 444 TCAE-93 4.4D Engines. Alternate part number: 28229876

Get help to fix this fault by requesting a quote

Browse other JCB codes