P2BAD-17

JCB P2BAD-17 – DCU: Exceeded the Limit Value of Long Term Adaptation Factor

Issue description

The engine's after-treatment system has detected that the long-term adaptation factor for the Diesel Exhaust Fluid (DEF) / AdBlue dosing has exceeded its predefined maximum limit. The Dosing Control Unit (DCU) has had to adjust DEF injection beyond the expected range to maintain required NOx reduction efficiency. This condition triggers a Tier 4 Final inducement, resulting in a reduction of engine power (derate) to encourage immediate service and prevent excessive emissions.

Applies to these machines

  • JS115
  • JS130
  • JS145
  • JS160
  • JS180
  • JS190
  • JS200
  • JS210
  • JS220
  • JS235
  • 527
  • 535
  • 550
  • JCB Ecomax Wheeled Loaders
  • JCB Ecomax Generators
  • JCB Ecomax Lighting Towers
  • JCB T4F 444 engine
  • JCB T4F 448 engine

Check the cause

  1. Check the DEF (AdBlue) level in the tank to ensure it is not overfilled, which can hinder pressure drop in the return line

  2. Inspect all DEF hoses for kinks, damage, or blockages

  3. Examine electrical connectors at the DCU and dosing module for moisture, corrosion ('green death'), debris, or unsecured pins

  4. Check the machine's primary earth points to ensure they are clean and secure

  5. Check for other active or stored fault codes (e.g., P2201 NOx sensors, P2047 DEF injector circuits, P20EE SCR efficiency) which could be the root cause

  6. Test DEF concentration using a refractometer (should be approximately 32.5%)

  7. Using JCB ServiceMaster, check DCU and ECU software versions (reflash if required) and verify DCU supply voltage (10V-16V for 12V machines, 19V-32V for 24V machines)

Repair steps

  1. Clear fault codes

    Clear the DTCs and check if the fault returns immediately.

  2. Perform DEF pump test

    Using JCB ServiceMaster, navigate to the DEF pump test and run the procedure. If the test fails, check the DEF harness for continuity and verify the ground connections are clean and tight.

  3. Inspect dosing module and nozzle

    Remove the dosing module. Check the injector nozzle for blockage from crystallized DEF and clean if necessary.

  4. Perform dosing quantity test

    In ServiceMaster, navigate to the 'DEF dosing quantity test' and run it. If this test fails, the dosing module is likely faulty and should be replaced.

  5. Check for system blockages

    If tests indicate pressure issues, check the DEF return line to the tank for any blockages and clear if necessary. Clean all DEF system filters to remove any potential debris.

  6. Replace and initialize components

    If the DCU or dosing module is identified as faulty, replace it. If a new dosing module is installed, it is critical to perform the 'dosing module initialisation' procedure using ServiceMaster.

  7. Final confirmation

    Clear all fault codes one last time. Perform a key cycle (ignition off for 1-2 minutes) and then operate the machine to ensure the fault does not reappear and that full engine power is restored.

Parts you might need

(5)
  • Genuine JCB. Also referenced as model DCU-17CV51.

  • Genuine JCB BOSCH Dosing module. Contains the injector nozzle. Replace if dosing quantity test fails.

  • Fuel Injector

    320/06828

    Delphi. For Ecomax Engine - for reference, NOT the DEF injector. Listed for clarity and to avoid confusion.

  • Fuel Injector320/06827

    Delphi. For Ecomax Engine - for reference, NOT the DEF injector. Listed for clarity and to avoid confusion.

  • Fuel Injector320/06623

    Delphi. For Ecomax Engine - for reference, NOT the DEF injector. Listed for clarity and to avoid confusion.

Get help to fix this fault by requesting a quote

Browse other JCB codes