JCB P3423-87 – Engine Control Unit (ECU) or related aftertreatment control module: Erroneous Signal for Engine Exhaust Gas Temperature
Issue description
The system detects an incorrect or unreliable signal related to the engine exhaust gas temperature, or a missing CAN message from the engine ECU. This indicates a problem with the component responsible for generating or transmitting this signal, such as the sensor itself, its wiring, or a CAN bus communication failure. The machine's reaction to this fault code often includes a reduction in engine torque to prevent potential damage.
Applies to these machines
21 machines- Tracked Excavators
- Wheeled Excavators
- JS Series Excavators
- JS130
- JS140
- JS180
- JS200
- JS205
- JS210
- JS220
- JS235
- JS240
- 131X
- Wheeled Loaders
- 411
- 413
- 417
- 419
- Generators with Tier 4 engines
- TM Series Telehandlers
- TM320
Check the cause
For sensor/wiring faults: Visually inspect the exhaust gas temperature sensor wiring harness for chafing, melting, or breaks, particularly near hot exhaust components or pivot points. Check the electrical connector for corrosion, bent or loose pins, and ensure it is securely connected.
For sensor/wiring faults: Disconnect the sensor and check for a 5-volt reference signal from the ECU at the connector with the ignition on (engine off).
For sensor/wiring faults: Measure the resistance (Ohms) across the disconnected sensor's terminals and compare to manufacturer specifications. An 'OL' (open circuit) or a reading far outside the expected range indicates a faulty sensor.
For sensor/wiring faults: Monitor live data with a diagnostic scan tool; a fixed reading (e.g., -40°C) or implausible jumps indicates a sensor or wiring failure.
For CAN communication faults: Inspect and clean all major machine ground connections. Check the primary connectors to the Engine ECU for security and signs of corrosion or water ingress.
For CAN communication faults: Visually inspect the CAN bus wiring harness for damage, pinching, or abrasion.
For CAN communication faults: Use JCB ServiceMaster to check for other active CAN bus error codes (e.g., U0073) which would confirm a wider network problem. Check the communication status of all modules on the network.
Repair steps
Prepare machine
Ensure the engine is off and completely cooled down. Disconnect the negative terminal of the battery to prevent electrical issues.
Locate sensor
Identify the correct exhaust gas temperature sensor specified by the fault (often located in the exhaust manifold or before the turbocharger).
Remove faulty sensor
Disconnect the electrical connector. Use an appropriate flare nut or sensor socket to unscrew the sensor. Apply penetrating oil beforehand if the sensor is seized.
Install new sensor
Apply a small amount of anti-seize compound to the threads if not pre-coated. Carefully thread the new sensor in by hand to avoid cross-threading.
Torque sensor
Tighten the sensor to the manufacturer's recommended torque specification using a torque wrench to avoid damaging the sensor or manifold.
Finalize connections
Reconnect the electrical connector until it clicks into place, then reconnect the negative battery terminal.
Clear codes and test
Use a diagnostic tool to clear the fault code. Start the engine, monitor live data from the new sensor to ensure it is reading correctly, and perform a road test or operate the machine to confirm the fault does not return.
Parts you might need
(5)- Exhaust Gas Temperature Sensor320/A9184
For Tier 4 machinery, generators, tracked excavators, and wheeled loaders with SCR systems.
- Exhaust Gas Temperature Sensor320/06233
For 131X, wheeled loaders (411, 413, 417, 419), and TM320 T4F.
- Exhaust Gas Temperature Sensor716/30111
For JCB 444 engine and JS series excavators (JS130, JS180, JS200, JS220, JS240).
Exhaust Gas Temperature Sensor
333/K3082For JS140, JS200, and JS205 excavators.
- Exhaust Gas Temperature Sensor400/K4211
General exhaust gas temp sensor.
Get help to fix this fault by requesting a quote