U059F-00

JCB U059F-00 – Aftertreatment System ECU: Upstream NOx Sensor Temp Signal CAN Error

Issue description

The engine's aftertreatment control system has detected a communication error with the upstream NOx sensor over the CAN bus. Specifically, the message containing the sensor's temperature status is missing, invalid, or not being received correctly. This prevents the system from monitoring the sensor's operational readiness, which typically triggers the Malfunction Indicator Lamp (MIL) and may force the machine into a reduced power mode to prevent excessive emissions and damage to the aftertreatment system.

Applies to these machines

  • EcoMAX Tier 4
  • JS Excavators
  • Crawler Excavators
  • 406 SV Wheel Loader
  • 409 SV Wheel Loader

Check the cause

  1. Review other active fault codes related to battery voltage, ignition, or other CAN bus communication errors. Diagnosing these first can prevent a misdiagnosis of the U059F-00 code.

  2. Thoroughly inspect the wiring harness and connectors for the upstream NOx sensor. Look for signs of damage such as chafing, rubbing, burn spots, bare wires, or melted plastic. Pay close attention to the routing of the harness to ensure it is not damaged.

  3. Disconnect the upstream NOx sensor and inspect the connector terminals for corrosion, debris, water ingress, or pushed-back/loose pins. Ensure all machine ground connections are clean and tight.

  4. Verify power and ground to the sensor using a multimeter or test lamp by checking for battery voltage at the power pin (with the ignition on) and a good ground connection on the corresponding ground pin.

  5. Check CAN bus circuit integrity by measuring the voltage on the CAN lines at the sensor connector (ignition on, engine off). You should see approximately 2.6V on CAN High and 2.4V on CAN Low, with slight fluctuations. If possible, use an oscilloscope to verify the presence of a clean, square-wave CAN signal on both lines, which confirms the network is communicating to the sensor plug.

  6. Using a diagnostic tool, monitor the live data from the upstream NOx sensor. If the readings for temperature or NOx concentration are frozen, erratic, or unresponsive, it points towards a faulty sensor, assuming the wiring and power supply have been verified as good.

Repair steps

  1. Address preliminary faults

    If any other power or communication faults were found, repair those issues first.

  2. Repair wiring and connectors

    If the diagnostic checks revealed any damage to the wiring harness or connectors, repair or replace the affected sections. Ensure all connections are clean, secure, and properly sealed.

  3. Replace upstream NOx sensor

    If the diagnostic checks confirm that the wiring, power, and ground are all correct, the fault lies with the upstream NOx sensor itself. Important: Stop the engine and allow the exhaust system to cool completely before attempting to remove the sensor. Disconnect the electrical connector from the sensor module. Unscrew the NOx sensor from the exhaust pipe. If it is seized, use penetrating oil and appropriate tools to avoid damaging the threads in the exhaust system. Install the new upstream NOx sensor and torque it to the manufacturer's specification. Connect the new sensor's electrical connector.

  4. Clear fault codes

    After the repair is complete, use a diagnostic tool to clear the U059F-00 fault code from the Aftertreatment ECU.

  5. Verify repair

    Start the engine and allow it to reach operating temperature. Monitor the live data from the new NOx sensor to ensure it is communicating and providing plausible readings. Perform a drive cycle or operate the machine to confirm that the fault code does not return.

Parts you might need

(1)
  • Upstream NOx Sensor (also referred to as NOx Sensor 1 or Pre-SCR NOx Sensor)

    OEM (Original Equipment Manufacturer) parts are highly recommended to ensure correct calibration and communication with the JCB control systems. NOx sensors are often sold as a complete assembly including the sensor probe and the integrated control module. To obtain the correct part number, it is necessary to contact a JCB dealer with the machine's model and serial number.

Get help to fix this fault by requesting a quote

Browse other JCB codes