U059F-08

JCB U059F-08 – ECU: Downstream NOx Sensor CAN Error

Issue description

The system has detected a CAN bus message error related to the O2 signal status from the downstream NOx sensor. The Engine Control Unit (ECU) expects to receive data about oxygen levels from the sensor via the CAN bus, but the message is missing, incomplete, or invalid. This indicates a communication issue with the sensor's data transmission, preventing the after-treatment system from correctly monitoring its performance. This fault typically results in a reduction in engine torque and triggers a 'SERVICE' warning to the operator.

Applies to these machines

  • Excavators
  • Loaders
  • Backhoes
  • Tier 4 Engine Machines
  • Stage V Engine Machines

Check the cause

  1. Record and clear the code using a diagnostic tool to see if it returns immediately under load (rules out a temporary 'ghost' fault caused by a voltage surge)

  2. Check battery voltage (must test above 12.5V) and inspect ground connections, as weak power can cause CAN bus communication errors

  3. Visually inspect the wiring harness connected to the downstream NOx sensor for rubbing, chafing, melting, or physical damage

  4. Disconnect the NOx sensor module connector and inspect for green corrosion, bent or pushed-out pins, and moisture intrusion

  5. Verify the NOx sensor module is receiving the correct power and has a solid ground connection using a multimeter

  6. Test the CAN bus circuit resistance between CAN High and CAN Low at the OBD port or sensor connector (should be approximately 60 Ohms)

  7. Check CAN bus voltage with the key on and engine off (CAN High should be 2.5-3.5V, CAN Low should be 1.5-2.5V)

  8. Unplug the downstream NOx sensor to see if the fault code changes, which helps isolate whether the fault lies within the sensor itself or the wiring harness

Repair steps

  1. Safety First

    Stop the engine and allow the exhaust system to cool completely before starting work. Disconnect the machine's battery to prevent accidental starting.

  2. Locate the Sensor

    Identify the downstream NOx sensor. It is screwed into the exhaust pipe after the SCR catalyst. It will have a wiring pigtail leading to a small control module mounted on the machine's frame.

  3. Perform Diagnostics

    Complete the diagnostic checks listed in the section above to rule out wiring, power, or network issues. A faulty sensor is often the cause, but these checks prevent unnecessary replacement.

  4. Replace the Sensor

    Disconnect the wiring harness from the NOx sensor module. Unbolt the sensor module from the frame. Using the correct size wrench, carefully unscrew the NOx sensor from the exhaust pipe. Apply a small amount of ceramic anti-seize compound to the threads of the new sensor, being careful not to get any on the sensor tip. Install the new sensor and torque it to the manufacturer's specification. Mount the new sensor module to the frame and connect the wiring harness.

  5. Initialization/Reset

    For some systems, a reset procedure using a diagnostic tool must be performed after replacing a NOx sensor to initialize the new component with the ECU.

  6. Final Verification

    Reconnect the battery, start the engine, and clear any related fault codes. Operate the machine to confirm that the fault code does not return.

Parts you might need

(8)
  • Engine NOx sensor (downstream)

    400/J4546

    Verify fitment by machine serial number

  • Sensor NOX downstream

    400/00829

    Verify fitment by machine serial number

  • NOx Sensor

    400/14470

    Verify fitment by machine serial number

  • Verify fitment by machine serial number

  • Verify fitment by machine serial number

  • NOx Sensor (Continental)

    332/J5063

    Verify fitment by machine serial number

  • NOx Sensor (Continental)

    332/J5065

    Verify fitment by machine serial number

  • Verify fitment by machine serial number

Get help to fix this fault by requesting a quote

Browse other JCB codes