000630.13

John Deere 000630.13 – Multiple Control Modules (SCO, HCU, PTI, ACU): Transmission Not Calibrated

Issue description

A specific control module indicates that the transmission system is not calibrated because the stored values for the transmission's clutches and valves are either missing or invalid. This calibration fault can negatively affect the proper operation and shift quality of the transmission system.

Applies to these machines

  • 8230T
  • 8330T
  • 8430T
  • 9230
  • 9330
  • 9430
  • 9530
  • 9630
  • 5080R
  • 5090R
  • 5100R
  • 6130
  • 6230
  • 6330
  • 6430
  • 6530
  • 6534
  • 6630
  • 6830
  • 6930
  • 9120
  • 9220
  • 9320T
  • 9420T
  • 9520T
  • 9620T

Check the cause

  1. Check the transmission-hydraulic oil level in the sight gauge and ensure it is warmed up to the specified temperature (typically above 35°C/95°F or 50°C/122°F depending on transmission type)

  2. Inspect for and address any other active fault codes, especially those related to sensors, solenoids, or power supply, before attempting calibration

  3. Verify that the park brake is functioning correctly

  4. Disable the Efficiency Manager™ system, if the machine is equipped with it

  5. Check for restricted transmission oil filters, which can negatively affect the calibration process

Repair steps

  1. Perform automatic calibration (IVT models)

    For Infinitely Variable Transmissions (IVT), trigger the automatic calibration by ensuring the engine is running below 1300 RPM, the transmission is in PARK for a continuous 20 seconds, and the transmission oil temperature is above 25°C (77°F). The process takes about 45 seconds.

  2. Perform manual calibration (IVT models)

    If a manual calibration is needed or if the automatic process is interrupted, it is recommended to have a John Deere dealer perform the calibration. The procedure involves heating the transmission oil, setting the throttle to 1000 RPM, and shifting to PARK.

  3. Prepare for manual calibration (Powershift models)

    Drive the tractor to a level surface, place the shift lever in the PARK position, and ensure the transmission-hydraulic oil is warmed up to the specified temperature (e.g., above 35°C or 95°F).

  4. Access diagnostic mode (Powershift models)

    Navigate through the CommandCenter™ display to Diagnostics, then Controllers, and select the PTP (Powershift Transmission) controller. Select calibration address PTP Address 025. The display should show 'CAL'.

  5. Initiate manual calibration (Powershift models)

    Set the engine speed to the specified RPM (e.g., 1600 RPM). Initiate calibration by moving the shift lever to the 'F' (Forward) or 'R' (Reverse) position. Do not interrupt the process by changing the throttle, moving the shift lever, or depressing the clutch pedal. Wait 12-15 minutes for completion.

  6. Record values and exit (Powershift models)

    Once calibration is complete and the display returns to normal, record the new clutch calibration values from PTP Address 27. Exit the calibration mode by throttling down, moving the shift lever to PARK, and following the specific exit sequence on the display to avoid setting new fault codes.

  7. Replace Transmission Control Module

    If the calibration procedure fails to resolve the issue or cannot be initiated, the Transmission Control Module itself may be faulty and require replacement.

Parts you might need

(11)
  • For models 5080R, 5090R, 5100R, 6930

  • Transmission Controller Module

    YZ106309

    Verify fitment by serial number

  • Transmission Control Module

    AT457457

    Verify fitment by serial number

  • Transmission Controller

    AT219930

    Verify fitment by serial number

  • Used Transmission Control Module

    YZ502168

    For models 9120, 9220, 9320T, 9420T, 9520T, 9620T

  • Used Transmission Control Module

    YZ502021

    For models 9120, 9220, 9320T, 9420T, 9520T, 9620T

  • Used Transmission Control Module

    YZ502121

    For models 9120, 9220, 9320T, 9420T, 9520T, 9620T

  • Used Transmission Control Module

    YZ502029

    For models 9120, 9220, 9320T, 9420T, 9520T, 9620T

  • Used Transmission Control Module

    YZ901504

    For models 9120, 9220, 9320T, 9420T, 9520T, 9620T

  • Used Transmission Control Module

    YZ502299

    For models 9120, 9220, 9320T, 9420T, 9520T, 9620T

  • Used Transmission Control Module

    YZ501816

    For models 9120, 9220, 9320T, 9420T, 9520T, 9620T

Get help to fix this fault by requesting a quote

Browse other John Deere codes