651.02

John Deere 651.02 – Engine Control Unit (ECU): Injector Number 1 Code Error / Cylinder No. 1 Electronic Injector Part Number Invalid

Issue description

The controller detects that the part number or calibration code of the electronic fuel injector installed in cylinder #1 is incorrect or invalid. This discrepancy can lead to improper fuel delivery, causing the system to adjust engine parameters or limit performance (derate) to prevent potential engine damage.

Applies to these machines

  • 5085E
  • 5090E
  • 5090EL
  • 5100E
  • 5065M
  • 5075M
  • 5085M
  • 5100M
  • 5100MH
  • 5100ML
  • 5115ML
  • 5095M
  • 5095MH
  • 5105M
  • 5015ML
  • 5090M
  • 5115M
  • 6110M
  • 6120M
  • 6130M
  • 6145M
  • 6155M
  • 6175M
  • 6195M
  • 6110R
  • 6120R
  • 6130R
  • 6145R
  • 6155R
  • 6175R
  • 6195R
  • 6215R
  • 7810
  • 9650 STS
  • 9750 STS
  • 4930
  • 130G
  • 160GLC
  • 310SK
  • 444K

Check the cause

  1. Physically inspect the fuel injector installed in cylinder #1 to ensure the stamped part number matches the specified OEM part number required for your exact engine model.

  2. Connect a diagnostic tool (such as John Deere Service ADVISOR) to verify the injector calibration code (QR code/trim code) programmed into the ECU for cylinder #1 matches the physical injector.

Repair steps

  1. Recalibrate the Injector

    If the physical part number on the injector is correct for the engine but the code is active, use the diagnostic tool to input the correct calibration code into the ECU for cylinder #1.

  2. Replace Incorrect Injector

    If the physical inspection reveals that the wrong injector was installed (often happens after a recent repair or engine swap), remove the incorrect injector and install the correct OEM part. Note: It is highly recommended to replace injectors as a matched set to prevent uneven atomization and vibrations.

  3. Program the New Injector

    If a replacement is installed, you must program the new injector's specific calibration code into the ECU.

  4. Reset and Verify

    Clear the fault codes from the ECU, cycle the key, and run the engine to verify that the injector operates correctly and the 000651.02 code does not return.

Parts you might need

(12)
  • Electronic Fuel Injector (Common Rail)

    RE556741

    New OEM

  • Electronic Fuel Injector (Common Rail)

    RE546784

    New OEM

  • Electronic Fuel Injector (Common Rail)

    RE531801

    New OEM

  • Electronic Fuel Injector (Common Rail)

    RE545562

    New OEM

  • Electronic Fuel Injector (Common Rail)

    DZ100212

    New OEM

  • Electronic Fuel Injector (Common Rail)

    SE502088

    Remanufactured OEM

  • Electronic Fuel Injector (Common Rail)

    SE502671

    Remanufactured OEM

  • Electronic Fuel Injector (Common Rail)

    SE501925

    Remanufactured OEM

  • Electronic Fuel Injector (Common Rail)

    095000-6310

    Denso Cross-Reference

  • Electronic Fuel Injector (Common Rail)

    295050-1430

    Denso Cross-Reference

  • Electronic Fuel Injector (Common Rail)

    095000-0590

    Denso Cross-Reference

  • Electronic Fuel Injector (Common Rail)

    AP52907

    Alliant Power Cross-Reference

Get help to fix this fault by requesting a quote

Browse other John Deere codes