John Deere 84.05 – CCU: Wheel Speed Sensor Open Circuit Low Amps
Issue description
The system has detected an open circuit or a low current condition in the wheel speed sensor's electrical circuit, resulting in the loss of a valid signal to the Main Control Module (CCU). This failure can be caused by a break in the wiring, a faulty sensor, or a poor connection. A loss of wheel speed data can lead to erratic transmission shifting, incorrect speed readouts, and the disabling of associated systems such as traction control and anti-lock brakes (ABS).
Applies to these machines
33 machines- 6110M
- 6120M
- 6130M
- 6145M
- 6155M
- 6175M
- 6195M
- 6110R
- 6120R
- 6130R
- 6145R
- 6155R
- 6175R
- 6195R
- 6215R
- 6090MC
- 6090RC
- 6100MC
- 6100RC
- 6110MC
- 6110RC
- 5075M
- 5090M
- 5095M
- 5100M
- 5115M
- 5125M
- 8225R through 8345R
- 8R 340 to 8R 540
- 8RX 410 to 8RX 540
- 8100-8600 series harvesters
- 643L-III
- 843L-III
Check the cause
Inspect the wheel speed sensor wiring harness for broken wires, and check the connectors for looseness, dirt, or corrosion. Clean all electrical connections thoroughly, as corrosion can cause intermittent open-circuit readings.
Use a digital multimeter (ohmmeter) or continuity tester to check the wiring harness between the sensor and the CCU. Wiggle the wires during testing to check for intermittent breaks.
Connect a diagnostic scan tool (such as John Deere Service Advisor). Monitor the wheel speed sensor PIDs in real-time while driving the tractor at a steady speed. Verify if the live speed reading matches the ground speed or if it drops to zero/behaves erratically.
If the sensor is reading erratically, check the air gap between the sensor tip and the tone ring. The typical adjustment requires a 0.5 mm to 1.5 mm gap, which is sometimes adjusted via washer shimming or threading.
Repair steps
Locate the Sensor
Find the faulty wheel speed sensor on the affected wheel hub, axle, or hydrostatic motor housing.
Remove the Old Sensor
Disconnect the electrical harness. Back off the locking nut and pull the O-ring back against the locking ring. Unthread and remove the sensor from the housing.
Install the New Sensor
Thread the new sensor in by hand until you feel the tip physically make contact with the tone ring inside the hub/motor.
Set the Air Gap
Once it touches the tone ring, back the sensor out exactly 1/2 to 1 full turn to establish the correct air gap (approx. 0.5 - 1.5 mm).
Secure the Sensor
If equipped with a sensor protector bracket, test the fit and install it. Tighten the locking ring/nut into the housing to compress the O-ring. Caution: Do not overtighten the locking nut.
Reconnect and Clear Codes
Reconnect the electrical harness. Use John Deere Service Advisor or a compatible scan tool to clear the stored 000084.05 fault code from the CCU.
Test Drive
Drive the machine and monitor the live data to ensure the new sensor is accurately tracking ground speed.
Parts you might need
(10)- Wheel Speed SensorRE330846
36 mm length. Fits a massive variety of modern platforms including 5000, 6M, 6R, 8R, 8RX series tractors, as well as various planters and harvesters.
- Wheel Speed SensorRE330848
65 mm length. Fits 6B, 6E, 6M, 6R, 8R, 8RX series, and various graders/loaders.
- Wheel Speed SensorRE295929
Cross-references to RE558874 and RE204888. Commonly used on 5045E, 5055E, 5065E, 5075E, and 7000 series tractors.
Hydrostatic Drive Motor Wheel Speed Sensor
AT342623Verify fitment by serial number
Wheel Motion and Height Wheel Speed Sensor
AA93261Verify fitment by serial number
Wheel Speed Sensor
AT342622Verify fitment by serial number
Right Wheel Speed Sensor Wiring Harness
AT453136Verify fitment by serial number
Wheel Speed Sensor
AUC12197Fits 6145R, 6155R, 6195R and others
- Magnetic Pickup SensorAL204621
Compatible with many 6M and 6R series tractors
- Wheel Speed Sensor (85mm)RE330849
85mm length wheel speed sensor
Get help to fix this fault by requesting a quote