000084.09

John Deere 000084.09 – ECU / ACU / BRC: Wheel Speed Sensor Communication Fault

Issue description

The fault code 000084.09 (SPN 84, FMI 9) indicates a communication error with the wheel-based vehicle speed sensor due to an abnormal update rate. The control unit is not receiving the speed signal at the expected frequency because the signal is missing, intermittent, or irregular. This loss of data affects systems that rely on wheel speed, such as the transmission, traction control, and speedometer, and may cause the machine to enter a limp mode with reduced speed.

Applies to these machines

  • 5000 Series
  • 6M Series
  • 6R Series
  • 7M Series
  • 8R Series
  • 8RT Series
  • 8RX Series
  • 319E
  • 323E
  • 325G
  • 329E
  • 333D
  • Combines
  • Planters
  • Harvesters
  • Gator Utility Vehicles
  • Dozers
  • Feller Bunchers

Check the cause

  1. Visually inspect the wheel speed sensor and its wiring harness for physical damage, chafed or broken wires, and corrosion on connectors

  2. Ensure all electrical connectors between the sensor and the control module are clean and securely fastened to rule out intermittent signals

  3. Clean the sensor head and surrounding area to remove any dirt, mud, or metal debris interfering with the reading

  4. Check for excessive wheel end play in the bearings, which can alter the air gap between the sensor and the tone ring

  5. Measure the resistance of the sensor and compare it to OEM specifications to identify a failed sensor

  6. Perform a wiring continuity and load test on the harness with the sensor and control unit disconnected to check for wires failing under load

Repair steps

  1. Park the Machine Safely

    Park the vehicle on a level surface, engage the parking brake, and block the wheels to prevent movement.

  2. Disconnect Power

    Disconnect the negative battery cable to prevent electrical issues during the repair.

  3. Gain Access to the Sensor

    Depending on the machine, this may require removing access panels or, in the case of some track loaders, removing the track.

  4. Remove the Old Sensor

    Disconnect the electrical connector from the sensor. Remove the retaining bolt (often an Allen key bolt) and carefully pull the sensor out of its housing. The sensor may be stuck due to corrosion; penetrating oil may be required. Be prepared for potential hydraulic fluid leakage on some models.

  5. Install the New Sensor

    Lightly lubricate the O-ring on the new sensor before installation. Insert the new sensor into the housing and secure it with the retaining bolt.

  6. Reconnect and Reassemble

    Connect the electrical connector to the new sensor. Reinstall any panels or components that were removed.

  7. Reconnect Power and Clear Codes

    Reconnect the battery cable. Use a diagnostic tool to clear the fault code.

  8. Calibrate the New Sensor (If Required)

    Some machines, such as sprayers, may require a calibration procedure for the new wheel speed sensor to ensure accurate speed readings. This typically involves driving a measured distance at a constant speed. For other models, a calibration may need to be performed by a dealer.

  9. Test Operation

    Operate the machine to verify that the fault code does not return and that systems relying on wheel speed (e.g., speedometer, transmission shifting) are functioning correctly.

Parts you might need

(8)
  • Fits a wide range of tractors (5M, 6M, 6R, 8R series), combines, planters, and harvesters

  • Wheel Speed Sensor

    AT372235

    Fits some compact track loaders and skid steer loaders (319E, 323E, 325G). Replaced by AT552279

  • Wheel Speed Sensor

    AT552279

    Replacement part for AT372235

  • Hydrostatic Drive Motor Wheel Speed Sensor

    AT342623
  • Wheel Speed Sensor

    SJ16388
  • Wheel Speed Sensor

    AN209159
  • 85mm length

Get help to fix this fault by requesting a quote

Browse other John Deere codes