E-61

Kubota E-61 – Transmission ECU: Solenoid 1 is in trouble (At forward or neutral) / 1, 7, 8th speed NG

Issue description

The Transmission ECU has detected a fault (such as an open circuit, short circuit, or voltage drop) in the electrical circuit for Proportional Valve Solenoid 1 on the Glide Shift Transmission (GST) valve block. When this shift solenoid fails or loses signal, the gearshift lever will physically remain in the same position, but the transmission ECU will automatically change the real speed to an operable, safe speed range or force the tractor into neutral.

Applies to these machines

  • L39
  • L45
  • L48
  • L3240
  • L3540
  • L3940
  • L4240
  • L4740
  • L5040
  • L5240
  • L5740
  • L3560
  • L4060
  • L4760
  • L5060
  • L5460
  • L6060
  • L3130
  • L3430
  • L3830
  • L4330
  • L4630
  • L5030

Check the cause

  1. Check Battery Voltage: Low system voltage can cause the GST solenoids to drop out and trigger Error 61. Test the battery open circuit (should be >12.7V) and under load while cranking (should not drop below 11V).

  2. Inspect Battery Cables: Check the earth cord (ground cable) and plus cord (positive cable). Loose, corroded, or damaged clamp-style battery terminals are a frequent culprit for GST solenoid codes.

  3. Inspect the Wiring Harness: Crawl under the tractor (typically on the left side, under the clutch platform/steering column area) and locate the GST valve block. Inspect the wiring harness and the connector going to the proportional valve for snagged, pulled loose, or broken wires.

  4. Test Solenoid Resistance: Disconnect the connector to Solenoid 1. Use a digital ohmmeter to measure the resistance across the terminal on the connector and the valve body to check if the internal coil is open or shorted.

Repair steps

  1. Prepare tractor

    Park the tractor on a level surface, lower all implements, turn off the engine, and remove the key.

  2. Locate GST valve

    Locate the GST valve assembly on the side of the transmission case.

  3. Clean valve block

    Thoroughly clean the exterior of the GST valve block to prevent dirt from entering the hydraulic system during removal.

  4. Disconnect connector

    Disconnect the electrical connector from Solenoid 1.

  5. Remove retaining cover/bolts

    Remove the retaining cover/bolts holding the proportional solenoid valve assembly to the GST block.

  6. Remove faulty solenoid

    Carefully pull the faulty solenoid out of the valve body.

  7. Lubricate O-rings

    Lubricate the O-rings on the new solenoid with clean Kubota Super UDT2 hydraulic fluid.

  8. Install new solenoid

    Insert the new solenoid into the GST valve block and torque the retaining bolts to factory specifications.

  9. Reconnect connector

    Reconnect the electrical connector.

  10. Check fluid and test

    Check the transmission fluid level and top off with Super UDT2 if any fluid was lost. Start the tractor, check for leaks, and test the GST shifting to ensure the code is cleared.

Parts you might need

(8)
  • Complete GST Valve Assembly (Older L-Series)

    TA040-99034
  • Complete GST Valve Assembly (Older L-Series)

    TA040-65010
  • Complete GST Valve Assembly (Older L-Series)

    TA040-65012
  • Complete GST Valve Assembly (Older L-Series)

    TA040-65015
  • Complete GST Valve Assembly (Older L-Series)

    TA040-99030
  • Complete GST Valve Assembly

    T1063-65004
  • Kubota Super UDT2 Synthetic Universal Trans-Hydraulic Fluid

    70000-40201

Get help to fix this fault by requesting a quote

Browse other Kubota codes