P0203

Kubota P0203 – ECU: TWV 3 Actuation System Open Circuit

Issue description

The Engine Control Unit (ECU) has detected an open circuit in the actuation system of the Two-Way Valve (TWV) for the cylinder 3 fuel injector. The ECU commanded the injector to open but did not detect the expected electrical response. This prevents the injector from firing, leading to engine misfires and operational issues.

Applies to these machines

  • V3800
  • V3800-CR-TE4
  • V3800-CR-TIE4
  • V3800-TIEF4
  • V3800-TIE5
  • V3307
  • V6108
  • M108X
  • SVL90-2
  • SVL95-2s
  • SVL97-2
  • M9960
  • M5-111
  • Sakai R2-4
  • Caterpillar C3.8
  • Bobcat T750
  • Bobcat T770
  • Bobcat S850

Check the cause

  1. Visually inspect the wiring harness and connector for the cylinder 3 injector for chafing, breaks, corrosion, or loose connections

  2. Check for other related fault codes using a diagnostic scan tool, such as misfire codes (e.g., P0303), which often accompany injector circuit faults

  3. Measure the resistance of the disconnected injector's coil with a multimeter (typical value is 0.2 to 0.8 ohms; an infinite reading indicates an internal open circuit)

  4. Perform a 'noid' light test by plugging it into the injector connector and cranking the engine to verify the electrical pulse from the ECU

  5. Perform a cylinder contribution test using a diagnostic scan tool to confirm cylinder 3 is not contributing to engine power

Repair steps

  1. Repair wiring and connectors

    If visual inspection reveals damage to the wiring harness or connector for cylinder 3, repair or replace the affected parts and ensure all connections are clean and secure.

  2. Replace the fuel injector

    If diagnostic tests (such as an infinite resistance reading) indicate an internal open circuit, replace the fuel injector for cylinder 3.

  3. Inspect ECU/PCM

    If the wiring is intact and the injector tests good, the fault may lie within the ECU's injector driver circuit. Consider this only after exhausting all other possibilities.

Parts you might need

(8)
  • Fuel Injector

    1J508-53052

    OEM Kubota part for V3800 engine (manufactured by Denso). Always cross-reference with the machine's serial number.

  • Fuel Injector

    1J508-53070

    OEM Kubota part for V3800 engine (manufactured by Denso). Always cross-reference with the machine's serial number.

  • Fuel Injector1J508-53074

    OEM Kubota part for V3800 engine (manufactured by Denso). Always cross-reference with the machine's serial number.

  • Fuel Injector1G514-53004

    OEM Kubota part for V3800 engine (manufactured by Denso). Always cross-reference with the machine's serial number.

  • Fuel Injector1J419-53002

    OEM Kubota part for V3800 engine (manufactured by Denso). Always cross-reference with the machine's serial number.

  • Fuel Injector1J550-53000

    OEM Kubota part for V3800 engine (manufactured by Denso). Always cross-reference with the machine's serial number.

  • Fuel Injector

    K1J500-53052

    OEM Kubota part for V3800 engine (manufactured by Denso). Always cross-reference with the machine's serial number.

  • Fuel Injector

    K1J500-53050

    OEM Kubota part for V3800 engine (manufactured by Denso). Always cross-reference with the machine's serial number.

Get help to fix this fault by requesting a quote

Browse other Kubota codes