Massey Ferguson 00.02.63 – Dash: Internal Issue With Dash Temperature
Issue description
The internal temperature sensor located inside the instrument cluster has detected a temperature that is out of normal operating bounds (overheating), or the internal sensor/circuit board itself has failed and is sending an erratic voltage signal.
Applies to these machines
40 machines- 7714
- 7715
- 7715S
- 7716
- 7716S
- 7718
- 7718S
- 7719
- 7720
- 7720S
- 7722
- 7722S
- 7724
- 7724S
- 7726
- 7726S
- Tier 4 (2015-2021)
- 4707
- 4708
- 4709
- 4710
- 5608
- 5609
- 5610
- 5611
- 5612
- 5613
- 5710SL
- 5711SL
- 5712SL
- 5713SL
- 7614
- 7615
- 7616
- 7618
- 7619
- 7620
- 7622
- 7624
- 7626
Check the cause
Check the tractor cab for extreme greenhouse heating and verify that the HVAC vents behind or around the dash are not blocked
Test the tractor's charging system for an overcharging alternator, which can cause the dash components to overheat
Check for accompanying codes like 00.02.61 or 00.03.32, which may indicate a wiring harness short or a bad ground causing excessive resistance and heat
Disconnect the battery for 15 minutes to reset the dash module. If the code returns immediately upon startup in a cold cab, the internal sensor or board has permanently failed
Repair steps
Disconnect Power
Disconnect the negative battery cable to prevent electrical shorts or CAN BUS spikes.
Remove Trim
Remove the steering column shrouds and the plastic dashboard trim panels surrounding the instrument cluster.
Unmount the Cluster
Remove the retaining screws or bolts holding the dash cluster assembly in the console.
Disconnect Harnesses
Carefully pull the cluster forward and unplug the multi-pin wiring harness connectors from the rear.
Install Replacement
Plug the wiring harnesses into the new instrument cluster and mount it into the console.
Reassemble and Reconnect
Reinstall all trim panels and reconnect the battery.
Dealer Programming
Have an authorized Massey Ferguson dealer connect the AGCO Electronic Diagnostic Tool (EDT) to program the tractor's configuration, hours, and tire sizes into the new dash.
Parts you might need
(9)Instrument Cluster / Dash Panel Assembly
3787409M97Varies by exact model/year, transmission, and serial number. Do not buy a used cluster from a different model without confirming compatibility.
Instrument Cluster / Dash Panel Assembly
3787409M96Varies by exact model/year, transmission, and serial number. Do not buy a used cluster from a different model without confirming compatibility.
Instrument Cluster / Dash Panel Assembly
3787409M93Varies by exact model/year, transmission, and serial number. Do not buy a used cluster from a different model without confirming compatibility.
Instrument Cluster / Dash Panel Assembly
3787409M92Varies by exact model/year, transmission, and serial number. Do not buy a used cluster from a different model without confirming compatibility.
Instrument Cluster / Dash Panel Assembly
3787412M95Varies by exact model/year, transmission, and serial number. Do not buy a used cluster from a different model without confirming compatibility.
Instrument Cluster / Dash Panel Assembly
3787412M93Varies by exact model/year, transmission, and serial number. Do not buy a used cluster from a different model without confirming compatibility.
Instrument Cluster / Dash Panel Assembly
3819552M91Varies by exact model/year, transmission, and serial number. Do not buy a used cluster from a different model without confirming compatibility.
Instrument Cluster / Dash Panel Assembly
3821950M92Varies by exact model/year, transmission, and serial number. Do not buy a used cluster from a different model without confirming compatibility.
Instrument Cluster / Dash Panel Assembly
3783470M97Varies by exact model/year, transmission, and serial number. Do not buy a used cluster from a different model without confirming compatibility.
Get help to fix this fault by requesting a quote
