0A.63.19

Massey Ferguson 0A.63.19 – tractor's onboard diagnostic system: External Hydraulic Valve 6 Issue

Issue description

Malfunction or communication error detected in the circuit or operation of the 6th external hydraulic remote valve (spool valve).

Applies to these machines

  • 7724S
  • 5712SL
  • 7722
  • 7722S
  • 5713SL
  • 7720S
  • 7716
  • 7718
  • T4
  • 7715
  • 5710SL
  • 7726
  • 7726S
  • 5711SL
  • 7718S
  • 7719
  • 7714
  • 7716S
  • 7720
  • Tier 4 (2015-2021)
  • 7715S
  • 7724
  • 4707
  • 4708
  • 4709
  • 4710
  • 5608
  • 5609
  • 5610
  • 5611
  • 5612
  • 5613
  • 7614
  • 7615
  • 7616
  • 7618
  • 7619
  • 7620
  • 7622
  • 7624
  • 7626

Check the cause

  1. Use a compatible diagnostic tool to confirm 0A.63.19 is active and check for any accompanying voltage or connection codes.

  2. Locate the #6 external hydraulic valve block at the rear of the tractor and inspect the electrical connector and wiring harness for physical damage, chafing, or corrosion.

  3. Disconnect the harness and check for bent or pushed-back pins.

  4. Test the resistance of the valve's solenoid to ensure it is within OEM specifications.

  5. Verify that the harness is delivering the correct voltage when the #6 remote is commanded from the cab.

Repair steps

  1. Power down the tractor, engage the parking brake, and relieve all hydraulic system pressure before servicing.

  2. Disconnect the electrical connector at the #6 external hydraulic spool valve.

  3. Clean the contacts using electrical contact cleaner.

    If the wiring harness is damaged, splice in a repair pigtail or replace the damaged harness section.

  4. Remove the retaining bolts for the #6 spool valve/solenoid assembly.

    Perform this if the wiring and voltage supply are good but the valve solenoid fails resistance testing.

  5. Install the replacement hydraulic spool valve or solenoid.

    Ensure all O-rings are properly seated to prevent leaks.

  6. Reconnect the electrical harness.

  7. Connect a diagnostic tool to clear the 0A.63.19 fault code from the system memory.

  8. Start the tractor and test the #6 hydraulic remote for proper operation and check for any hydraulic leaks.

Parts you might need

(8)
  • External Hydraulic Valve / Auxiliary Spool Valve

  • Rexroth Hydraulic Electric Spool Valve (4-Pin)

    3797234M6

    Fitment: 6400, 6600, 7400, and 7600 Series tractors.

  • Spool Valve / Distribution Valve

    3796029M3
  • Hydraulic Spool Valve

    3795751M3
  • Hydraulic Auxiliary Spool Valve (with load sensing)

    3108256M1

    Fitment: 6100 Series (e.g., 6170, 6190).

  • Hydraulic Auxiliary Spool Valve (with load sensing)

    3796083M3

    Fitment: 6100 Series (e.g., 6170, 6190).

  • Hydraulic Spool Valve Assembly

    1696239M93

    Fitment: Various utility models including 200, 300, 500, and 600 series.

  • Hydraulic Spool Valve Assembly

    1696239M92

    Fitment: Various utility models including 200, 300, 500, and 600 series.

Get help to fix this fault by requesting a quote

Browse other Massey Ferguson codes