000102.03

Massey Ferguson 000102.03 – ECU: Intake Boost Pressure Sensor Signal Too High

Issue description

The Engine Control Unit (ECU) has detected a voltage from the intake boost pressure sensor that is higher than the expected range (typically exceeding 4.5 to 4.7 volts). This 'Signal Too High' or 'Shorted To High Source' condition usually indicates a short circuit in the signal wire to a positive voltage source, an open in the sensor's ground circuit, or a faulty sensor outputting abnormally high voltage. This data is critical for the ECU to calculate the correct air-fuel mixture, manage turbocharger boost levels, and control ignition timing.

Applies to these machines

  • 4607 M
  • 4608
  • 4609
  • 4609 M
  • 4610
  • 4610 M
  • 4707
  • 4708
  • 4709
  • 4710
  • 5460
  • 5465
  • 5470
  • 5475
  • 5480
  • 5608
  • 5609
  • 5610
  • 5611
  • 5612
  • 5613
  • 5710
  • 5711
  • 6460
  • 6465
  • 6470
  • 6475
  • 6480
  • 6485
  • 6490
  • 6495
  • 6497
  • 6499
  • 6612
  • 6613
  • 6614
  • 6615
  • 6616
  • 6711R
  • 6712
  • 6712R
  • 6713
  • 6713R
  • 7465
  • 7475
  • 7480
  • 7485
  • 7490
  • 7495
  • 7497
  • 7499
  • 7614
  • 7615
  • 7616
  • 7618
  • 7619
  • 7620
  • 7622
  • 7624
  • 7626
  • 7714
  • 7715
  • 7716
  • 7718
  • 7719
  • 7720
  • 7722
  • 7724
  • 7726
  • 8727 S
  • 8730 S
  • 8735 S
  • 8737 S
  • 8740 S
  • 3630 Xtra
  • 3640 Xtra
  • 3650 Xtra
  • 3660 Xtra
  • 1734E
  • 1739E
  • Beta Combines

Check the cause

  1. Visually inspect the intake boost pressure sensor, electrical connector, and wiring harness for damage, corrosion, moisture, or loose connections.

  2. Ensure the port where the sensor is mounted on the intake manifold is not clogged with soot or debris.

  3. Verify the 5V reference power supply from the ECU to the sensor connector (should be approximately 5 volts).

  4. Check the ground circuit resistance from the sensor connector to a known good chassis ground (should be less than 0.5 ohms).

  5. Test the signal wire for a short to power by measuring voltage with the sensor disconnected and key ON (should be close to 0 volts).

  6. Test the sensor output voltage by back-probing the signal wire with the sensor connected (should be 1.5-2.0V at atmospheric pressure, drop to 1.0-1.5V at idle, and increase with throttle).

Repair steps

  1. Repair wiring harness

    If diagnostic checks reveal shorts to a power source, open circuits (especially in the ground circuit), or corroded connectors, repair or replace the affected sections of the wiring harness.

  2. Replace the intake boost pressure sensor

    If the wiring is confirmed to be in good condition and the sensor fails the voltage output tests (e.g., signal voltage is stuck near 5V and does not change with manifold pressure), replace the sensor.

  3. Clear fault codes

    After completing the repairs, use a diagnostic tool to clear the fault code from the ECU's memory.

  4. Verify repair

    Operate the machine to ensure the fault code does not return and that the engine is performing correctly.

Parts you might need

(10)
  • OEM AGCO part, alternate part number V836666980. Compatible with a wide range of models.

  • Boost Pressure Sensor

    7064663M2

    Fits MF 1734E and MF 1739E models.

  • Boost Sensor

    4308786M11

    Suitable for models such as the Massey Ferguson 6485.

  • Boost SensorV837070201

    Listed for a broad range of Massey Ferguson series, including Beta combines and tractors with Sisu engines.

  • Common on 5700 series and newer

  • Intake Manifold Pressure Sensor (Boost Pressure Sensor)

    7064664M1
  • Intake Manifold Pressure Sensor (Boost Pressure Sensor)

    0281006102

    Bosch OEM Part Number

  • Intake Manifold Pressure Sensor (Boost Pressure Sensor)

    0281002743

    Bosch OEM Part Number

  • Intake Boost Pressure Sensor / Manifold Air Pressure (MAP) Sensor

    0281002576

    Bosch equivalent

Get help to fix this fault by requesting a quote

Browse other Massey Ferguson codes