001132.04

Massey Ferguson 001132.04 – ECU: Air Inlet Temperature Sensor Signal Voltage Low

Issue description

The Engine Control Unit (ECU) has detected an abnormally low voltage signal from the Air Inlet Temperature Sensor. This indicates a potential issue with the sensor itself, the wiring, or the electrical connector. The Air Inlet Temperature Sensor measures the temperature of the air entering the engine, which the ECU uses to calculate the correct air-fuel mixture for optimal combustion and engine performance.

Applies to these machines

  • 4707
  • 4708
  • 4709
  • 4710
  • 5608
  • 5609
  • 5610
  • 5611
  • 5612
  • 5613
  • 5710SL
  • 5711SL
  • 5712SL
  • 5713SL
  • 7614
  • 7615
  • 7616
  • 7618
  • 7619
  • 7620
  • 7622
  • 7624
  • 7626
  • 7714
  • 7715
  • 7715S
  • 7716
  • 7716S
  • 7718
  • 7718S
  • 7719
  • 7720
  • 7720S
  • 7722
  • 7722S
  • 7724
  • 7724S
  • 7726
  • 7726S
  • 8727S
  • 8730S
  • 8732S

Check the cause

  1. Visually inspect the Air Inlet Temperature Sensor and its electrical connector for damage, corrosion, or loose connections. Ensure no wires have pulled out of the connector (re-insert until it clicks if so).

  2. With the ignition on, disconnect the sensor and use a digital multimeter to check for a supply voltage of approximately 5 volts at the connector.

  3. Perform a resistance test on the disconnected sensor. At ambient temperature (around 25°C or 77°F), resistance should be between 2.0 and 6.0 kΩ.

  4. Test the sensor's reaction to temperature changes by gently warming it with a heat gun. Resistance should decrease steadily as temperature increases (e.g., around 300 Ω at 80°C or 176°F). Sudden jumps or dead spots indicate a faulty sensor.

  5. Inspect the wiring harness leading to the sensor for any signs of damage, such as chafing, breaks, or shorts.

Repair steps

  1. Disconnect the Battery

    For safety, disconnect the negative battery terminal.

  2. Locate the Sensor

    Identify the location of the Air Inlet Temperature Sensor in the engine's air intake system.

  3. Disconnect the Electrical Connector

    Carefully release the locking tab and disconnect the electrical connector from the sensor.

  4. Remove the Old Sensor

    Depending on the mounting, you may need to unscrew the sensor or use a small screwdriver to help pry it out of its housing.

  5. Install the New Sensor

    Lightly lubricate the O-ring of the new sensor to aid installation. Press the new sensor firmly into place until it is fully seated.

  6. Reconnect the Electrical Connector

    Attach the electrical connector to the new sensor, ensuring it clicks into place and the locking tab is secure.

  7. Reconnect the Battery

    Reconnect the negative battery terminal.

  8. Clear Fault Codes

    Use a diagnostic tool to clear the 001132.04 fault code from the ECU.

  9. Verify the Repair

    Start the engine and let it run to ensure the fault code does not reappear.

Parts you might need

(3)
  • Verify correct part number for your specific tractor model and serial number with an authorized dealer.

  • Verify correct part number for your specific tractor model and serial number with an authorized dealer.

  • Also fits Challenger tractors. Verify correct part number for your specific tractor model and serial number with an authorized dealer.

Get help to fix this fault by requesting a quote

Browse other Massey Ferguson codes