000157.02

Massey Ferguson 000157.02 – ECU: Fuel Rail Pressure Erratic

Issue description

The Engine Control Unit (ECU) has detected unstable or inconsistent pressure in the common rail fuel system, indicating an inconsistency in the fuel pressure regulation system. The ECU registers erratic signals from the fuel rail pressure sensor, which can negatively affect engine performance, cause rough running, or lead to starting issues.

Applies to these machines

  • 4607M
  • 4608
  • 4609
  • 4609M
  • 4610
  • 4610M
  • 4707
  • 4708
  • 4709
  • 4710
  • 5608
  • 5609
  • 5610
  • 5611
  • 5612
  • 5613
  • 5709 S
  • 5710
  • 5710 S
  • 5711
  • 5711 S
  • 5712 S
  • 5713 S
  • 6465
  • 6475
  • 6480
  • 6485
  • 6490
  • 6495
  • 6497
  • 6499
  • 6612
  • 6613
  • 6614
  • 6615
  • 6616
  • 7614
  • 7615
  • 7616
  • 7618
  • 7619
  • 7620
  • 7622
  • 7624
  • 7626
  • 7714
  • 7715
  • 7716
  • 7718
  • 7719
  • 7720
  • 7722
  • 7724
  • 7726
  • 8650
  • 8660
  • 8670
  • 8680
  • 8690
  • 8727
  • 8730
  • 8732
  • 8735
  • 8737
  • 8740

Check the cause

  1. Check for other active or stored fault codes related to fuel supply, injector circuits, or other sensors to provide context.

  2. Inspect the low-pressure fuel system for root causes, including sufficient fuel level and quality, clogged or dirty fuel filters, air in the fuel system, and proper lift pump function.

  3. Inspect the fuel rail pressure sensor's wiring harness and connector for signs of corrosion, damage, loose pins, or chafing, and ensure the connector is securely attached to the sensor.

  4. Perform a reference voltage test on the sensor circuit (should be approximately 5.0 volts between the 5-volt reference wire and a known good ground with ignition on, engine off).

  5. Perform a ground circuit test (resistance between the sensor's ground terminal and battery negative should be less than 0.5 ohms).

  6. Perform a dynamic signal voltage test by back-probing the signal wire (voltage should be stable between 1.2V and 1.5V at idle, and rise smoothly towards 3.5V - 4.0V during sharp acceleration). If the voltage is stuck, jumps erratically, or does not respond to changes in engine speed, the sensor is likely faulty.

Repair steps

  1. Relieve fuel pressure

    Ensure the engine is off and cool. Relieve any pressure in the high-pressure fuel rail according to the manufacturer's specific procedure. Always wear appropriate safety glasses and gloves.

  2. Remove the old sensor

    Locate the fuel rail pressure sensor threaded directly into the common fuel rail. Carefully disconnect the electrical connector, place a rag underneath to catch residual fuel, and use the appropriate size wrench to loosen and remove the old sensor.

  3. Install the new sensor

    Ensure the threads on the new sensor and the port in the fuel rail are clean. Thread the new sensor in by hand to avoid cross-threading, then tighten to the manufacturer's specified torque. Do not overtighten.

  4. Finalize and test

    Securely reconnect the electrical connector. Bleed the fuel system if required by the service manual to remove any air. Start the engine, check for fuel leaks around the new sensor, clear the fault codes using a diagnostic scanner, and run the engine to ensure the 000157.02 code does not reappear.

Parts you might need

(15)
  • AGCO (OEM) or aftermarket suppliers like GRANIT.

  • Fuel Pressure Sensor / Rail Pressure Sensor

    V837079434

    Alternative/superseded number.

  • Alternative/superseded number.

  • OEM Part Number. Manufactured by Bosch or other specialized electronics suppliers; typically has a 3-pin connector and an M18 x 1.5 thread.

  • Fuel Rail Pressure Sensor

    ACP0307650

    Listed for 2600H series tractors. Manufactured by Bosch or other specialized electronics suppliers; typically has a 3-pin connector and an M18 x 1.5 thread.

  • Fuel Rail Pressure Sensor

    504382373

    Cross-references to a sensor fitting 5600, 6600, 7600, 8600, and 8700 series. Manufactured by Bosch or other specialized electronics suppliers; typically has a 3-pin connector and an M18 x 1.5 thread.

  • Fuel Rail Pressure Sensor

    50438237

    Cross-references to a sensor fitting 5600, 6600, 7600, 8600, and 8700 series. Manufactured by Bosch or other specialized electronics suppliers; typically has a 3-pin connector and an M18 x 1.5 thread.

  • Perkins equivalent U5MK1236.

  • Fuel Rail Pressure Sensor (3-Pin)

    0281002937

    Bosch (OEM Manufacturer)

  • Fuel Rail Pressure Sensor (3-Pin)

    0281006177

    Bosch (OEM Manufacturer)

  • Fuel Rail Pressure Sensor (3-Pin)

    0281006361

    Bosch (OEM Manufacturer)

  • Fuel Rail Pressure Sensor (3-Pin)

    400250

    AGCO / Massey Ferguson

  • Fuel Rail Pressure Sensor (3-Pin)

    U5MK1087

    Perkins (Engine OEM)

  • Perkins (Engine OEM)

  • Fuel Rail Pressure Sensor (3-Pin)

    T410762

    Perkins (Engine OEM)

Get help to fix this fault by requesting a quote

Browse other Massey Ferguson codes