Massey Ferguson 000168.00 – ECU: Battery Voltage High (ECU)
Issue description
The Engine Control Unit (ECU) has detected that the system's battery voltage is above the normal operating range for a sustained period (e.g., exceeding 16 volts on a 12-volt system or 32-36 volts on a 24-volt system). This overvoltage condition indicates an issue with the power supply or voltage regulation and poses a significant risk of damage to sensitive electronic components.
Applies to these machines
38 machines- 4707
- 4708
- 4709
- 4710
- 5608
- 5609
- 5610
- 5611
- 5612
- 5613
- 5710
- 5711
- 5712
- 5713
- 6612
- 6613
- 6614
- 6615
- 6616
- 7614
- 7615
- 7616
- 7618
- 7619
- 7620
- 7622
- 7624
- 7626
- 7700 Series
- 8727
- 8730
- 8732
- 8735
- 8737
- 8740
- 6400 Series
- 7400 Series
- 8400 Series
Check the cause
Verify battery condition with the engine off. A fully charged 12-volt battery should read approximately 12.6 volts. Inspect terminals for corrosion and check for signs of overcharging, such as a swelling battery case or leaking acid.
Test charging system voltage with the engine running. Measure the voltage across the battery terminals. Normal charging voltage is between 13.5 and 14.5 volts. A reading above 15 volts confirms an overcharging problem.
Inspect wiring and connections between the alternator, battery, and ECU. Look for frayed, burnt, or loose wires and connectors. Pay close attention to ground connections, as a poor ground can cause the voltage regulator to malfunction and lead to overcharging.
Check the alternator drive belt to ensure it is in good condition and properly tensioned.
Repair steps
Disconnect the Battery
For safety, always disconnect the negative battery cable before beginning any electrical repairs.
Access the Alternator
Locate the alternator on the engine. It may be necessary to remove panels or other components to gain access.
Remove the Alternator
Disconnect the wiring harness from the back of the alternator. Loosen the belt tensioner and remove the serpentine belt from the alternator pulley. Remove the mounting bolts that secure the alternator to the engine block and remove the alternator from the tractor.
Install the New Alternator
Position the new alternator and secure it with the mounting bolts. Reinstall the serpentine belt, ensuring it is correctly routed and tensioned. Reconnect the electrical wiring harness to the new alternator.
Reconnect and Test
Reconnect the negative battery cable. Start the engine and use a multimeter to verify that the charging voltage at the battery is now within the correct range (13.5-14.5 volts).
Clear Fault Codes
Use an appropriate diagnostic tool to clear the 000168.00 fault code from the ECU's memory.
Parts you might need
(3)- Alternator (180-amp)4357844M4
Fits 5600, 6600, 7600, 7700, and 8700 series. Alternate part numbers include 4357844M3 and 4357844M2.
Alternator (12-volt, 120-amp Valeo)
4357550M1Fits 5611-5613, 5710-5713, 6614-6616, 7614-7622, 8727-8740. Alternate part numbers include 4357550M2 and 4357550M3.
- Alternator (14-volt, 150-amp)4281880M93
Fits some 6400, 7400, and 8400 series tractors. Alternate part numbers include 3789453M91, V836667315, and 3909639M1.
Get help to fix this fault by requesting a quote