003222.03

Massey Ferguson 003222.03 – ECU: NOx Sensor Before DOC Signal Issue

Issue description

The Engine Control Unit (ECU) has detected an abnormal signal from the upstream NOx sensor located before the Diesel Oxidation Catalyst (DOC). This sensor measures the concentration of nitrogen oxides in the exhaust gas before it enters the after-treatment system, which is crucial for the Selective Catalytic Reduction (SCR) system to accurately calculate and inject the correct amount of Diesel Exhaust Fluid (DEF). A signal issue can be caused by a disconnected sensor, an internal sensor fault, or a problem with the wiring or connectors, which may negatively affect emissions control and engine performance.

Applies to these machines

  • 4707
  • 4708
  • 4709
  • 4710
  • 5608
  • 5609
  • 5610
  • 5611
  • 5612
  • 5613
  • 5709M
  • 5710M
  • 5711M
  • 5712M
  • 5713M
  • 5710SL
  • 5711SL
  • 5712SL
  • 5713SL
  • 6713S
  • 6714S
  • 6715S
  • 6716S
  • 6S.135
  • 6S.145
  • 6S.155
  • 6S.165
  • 6S.180
  • 7S.155
  • 7S.165
  • 7S.180
  • 7S.190
  • 7S.210
  • 7614
  • 7615
  • 7616
  • 7618
  • 7619
  • 7620
  • 7622
  • 7624
  • 7626
  • 7714
  • 7715
  • 7715S
  • 7716
  • 7716S
  • 7718
  • 7718S
  • 7719
  • 7720
  • 7720S
  • 7722
  • 7722S
  • 7724
  • 7724S
  • 7726
  • 7726S

Check the cause

  1. Read and document all Diagnostic Trouble Codes (DTCs) using a professional diagnostic tool to check for broader after-treatment system issues.

  2. Visually inspect the NOx sensor's electrical connector and wiring harness for signs of corrosion, damage, loose connections, or chafing against hot exhaust components.

  3. Check heater circuit resistance by measuring across the heater pins with the sensor disconnected and the exhaust cool (a reading outside the typical 2-6 Ohms range indicates a failed internal heater element).

  4. Monitor live NOx values using a diagnostic tool with the engine running and warmed up (at idle, the upstream sensor should typically read between 150 and 400 ppm) and compare with downstream sensor readings for plausibility.

  5. Inspect the sensor for contamination from oil, coolant, or excessive soot, which can indicate other underlying engine issues.

Repair steps

  1. Locate the Faulty NOx Sensor

    The upstream NOx sensor is located in the exhaust system before the Diesel Oxidation Catalyst (DOC) and the SCR catalyst.

  2. Allow the Exhaust to Cool

    Ensure the exhaust system is cool to the touch to prevent burns and damage to the new sensor during installation.

  3. Remove the Sensor and Module

    Disconnect the electrical connector from the module. Remove the screws holding the module to its mounting bracket and then carefully remove the sensor probe from the exhaust pipe. A special open-ended socket may be required to fit over the sensor's wiring. If seized, penetrating oil may be necessary. In severe cases, the top of the sensor may need to be cut off to allow a standard deep-well socket to be used for removal.

  4. Clean the Threads

    Thoroughly clean the threads in the exhaust pipe bung using a thread chaser (M20 x 1.5) to ensure a smooth installation and proper sealing of the new sensor.

  5. Install the New Sensor

    Apply a small amount of ceramic anti-seize compound to the threads of the new sensor, being careful not to get any on the sensor tip. Thread the new sensor into the exhaust bung and tighten it to the manufacturer's specified torque.

  6. Install the New Module

    Mount the new NOx sensor module onto its bracket and securely connect the electrical connector. Ensure the wiring is neatly tied up and not rubbing against any other components to prevent future damage.

  7. Clear Fault Codes and Perform Relearn Procedure

    Use a diagnostic tool to clear all fault codes from the ECU. Some vehicles may require a NOx sensor relearn or calibration procedure to be performed after replacement.

Parts you might need

(12)
  • AGCO OEM part. Verify fitment by serial number.

  • AGCO OEM part. Verify fitment by serial number.

  • NOx Sensor (Upstream/Before DOC)

    72622868

    AGCO OEM part. Verify fitment by serial number.

  • NOx Sensor (Upstream/Before DOC)

    ACW1813980

    AGCO OEM part. Verify fitment by serial number.

  • AGCO OEM part. Verify fitment by serial number.

  • AGCO OEM part. Verify fitment by serial number.

  • NOx Sensor (Upstream/Before DOC)

    SNS155A

    Continental/UniNOx OEM supplier part. Verify fitment by serial number.

  • NOx Sensor (Upstream/Before DOC)

    5WK96755A

    Continental/UniNOx OEM supplier part. Verify fitment by serial number.

  • NOx Sensor (Upstream/Before DOC)

    A2C95912900-01

    Continental/UniNOx OEM supplier part. Verify fitment by serial number.

  • NOx Sensor (Upstream/Before DOC)

    A2C95912900-02

    Continental/UniNOx OEM supplier part. Verify fitment by serial number.

  • NOx Sensor (Before DOC / Upstream)

    ACX2371980

    AGCO / Massey Ferguson OEM

  • NOx Sensor (Before DOC / Upstream)

    184470

    FEBI BILSTEIN Aftermarket

Get help to fix this fault by requesting a quote

Browse other Massey Ferguson codes