Massey Ferguson 3224.03 – Engine ECU: NOx Sensor Before DOC Signal Issue. (ECU)
Issue description
The Engine Control Unit (ECU) has detected a problem with the electrical signal from the Nitrogen Oxide (NOx) sensor positioned upstream (before) the Diesel Oxidation Catalyst (DOC). The signal is out of the expected range, intermittent, or absent, which hinders the ECU's ability to accurately monitor and manage the engine's exhaust after-treatment system. This condition may negatively affect emissions control and engine performance, and will typically activate warning lights on the instrument panel.
Applies to these machines
48 machines- 4710
- 7724S
- 5712SL
- 7722S
- 7722
- 5713SL
- 7720S
- 7716
- 7718
- T4
- 7715
- 5710SL
- 7726
- 4708
- 7726S
- 4707
- 4709
- 5711SL
- 7718S
- 7719
- 7714
- 7716S
- T4 (2015-2021)
- 7720
- Tier 4 (2015-2021)
- 7715S
- 7724
- 5608
- 5609
- 5610
- 5611
- 5612
- 5613
- 5710 SL
- 5711 SL
- 5712 SL
- 5713 SL
- 7614
- 7615
- 7616
- 7618
- 7619
- 7620
- 7622
- 7624
- 7626
- 7714 to 7726
- 8727 to 8740
Check the cause
Inspect the wiring harness leading to the NOx sensor before the DOC for chafed wires, melted insulation from exhaust heat, or physical damage
Disconnect the NOx sensor control module connector and check for water intrusion, bent pins, or corrosion
Verify that the sensor is receiving proper supply voltage (12V or 24V) and has a solid ground (a missing ground can cause a Voltage Above Normal FMI 03 fault)
Verify CAN High and CAN Low resistance and voltage on the auxiliary engine CAN bus
Ensure there are no exhaust leaks upstream of the DOC, as unmetered air can skew sensor readings
Repair steps
Power Down
Turn the tractor's main battery disconnect switch to the OFF position before handling electrical or emissions components.
Locate the Sensor
Locate the upstream NOx sensor. It consists of two parts permanently joined by a cable: a sensor head threaded into the exhaust pipe (before the DOC) and a small control unit bolted to the chassis/bracket.
Disconnect
Unplug the electrical connector from the NOx sensor control unit.
Remove Sensor Head
Unbolt the control unit. Then, using a specialized NOx sensor socket or a 22mm wrench, carefully unscrew the sensor head from the exhaust pipe. (Note: The sensor head thread is M20x1.5. Penetrating oil may be required if it is seized).
Install New Sensor
Thread the new sensor head into the exhaust pipe. Torque the sensor head to exactly 50 Nm (37 lb-ft).
Mount Control Unit
Secure the new sensor's control unit to its mounting bracket.
Reconnect & Clear
Reconnect the electrical harness. Turn the battery switch back on, connect a diagnostic tool (like AGCO EDT), clear the inactive 003224.03 fault code, and run the engine to verify the repair.
Parts you might need
(4)- NOx Sensor (Before DOC / Upstream)ACW1305320
Primary OEM Part Number. 5-pin, 12V sensor with an M20x1.5 thread.
- NOx Sensor (Before DOC / Upstream)V837084094
Legacy part number.
- NOx Sensor (Before DOC / Upstream)ACX2480970
Alternative OEM Part Number. Fitment varies slightly by specific engine tier and chassis; always verify with the tractor's serial number.
NOx Sensor (Before DOC / Upstream)
ACX4946160Alternative OEM Part Number. Fitment varies slightly by specific engine tier and chassis; always verify with the tractor's serial number.
Get help to fix this fault by requesting a quote