3225.03

Massey Ferguson 3225.03 – Engine Control Unit (ECU): NOx Sensor Before DOC Signal Issue

Issue description

The Engine Control Unit (ECU) has detected an abnormal, out-of-range, or missing signal from the NOx sensor located upstream of the Diesel Oxidation Catalyst (DOC). This sensor measures the concentration of nitrogen oxides in the exhaust gas before it enters the after-treatment system. A malfunction prevents the ECU from properly managing the fuel mixture and DEF dosing for the SCR system, which can lead to increased emissions, poor fuel economy, and a reduction in engine power as the system enters limp mode to prevent damage.

Applies to these machines

  • 4710
  • 7724S
  • 5712SL
  • 7722S
  • 7722
  • 5713SL
  • 7720S
  • 7716
  • 7718
  • T4
  • 7715
  • 5710SL
  • 7726
  • 4708
  • 7726S
  • 4707
  • 4709
  • 5711SL
  • 7718S
  • 7719
  • 7714
  • 7716S
  • T4 (2015-2021)
  • 7720
  • Tier 4 (2015-2021)
  • 7715S
  • 7724
  • 5608
  • 5609
  • 5610
  • 5611
  • 5612
  • 5613
  • 5708
  • 5709
  • 5710
  • 5711
  • 5712
  • 5713
  • 6711
  • 6712
  • 6713
  • 6714
  • 6715
  • 6716
  • 6718
  • 7614
  • 7615
  • 7616
  • 7618
  • 7619
  • 7620
  • 7622
  • 7624
  • 7626
  • 8727
  • 8730
  • 8732
  • 8735
  • 8737
  • 8740

Check the cause

  1. Inspect the wiring harness and connector for the upstream NOx sensor for heat damage, chafed wires, water ingress, or corrosion

  2. Remove the sensor and inspect the probe for heavy soot buildup or moisture contamination

  3. Use a multimeter to verify that the sensor is receiving proper supply voltage and has a solid ground

  4. Check for exhaust leaks upstream of the sensor, as escaping exhaust gases or introduced oxygen can skew readings

  5. Use a diagnostic scan tool to monitor live data for the upstream NOx sensor to see if the voltage/ppm readings are dead or fluctuating wildly

Repair steps

  1. Repair Wiring

    If the diagnostic checks reveal damaged wiring or a corroded connector, repair the harness or replace the pigtail connector.

  2. Replace the Sensor

    If the wiring is intact and the sensor has failed internally, replace the upstream NOx sensor. Do not swap the upstream (Before DOC) and downstream (Outlet SCR) sensors as they have unique CAN identification numbers and are not interchangeable.

  3. Reassembly

    Install the new sensor into the exhaust pipe and torque it to the manufacturer's specification. Route the wiring carefully away from extreme heat sources.

  4. Clear Codes and Calibrate

    Connect a diagnostic scan tool to clear the 003225.03 fault code.

  5. Drive Cycle

    Perform a forced SCR system test via the scan tool or run the tractor under load to allow the ECU to validate the new sensor's signal.

Parts you might need

(5)
  • Upstream NOx Sensor (NOx Sensor Before DOC)

    V837084094

    OEM AGCO / Massey Ferguson

  • OEM AGCO / Massey Ferguson

  • OEM AGCO / Massey Ferguson

  • Upstream NOx Sensor (NOx Sensor Before DOC)

    A2C1307490001

    Continental/VDO

  • Upstream NOx Sensor (NOx Sensor Before DOC)

    A2C6253311466

    Continental/VDO

Get help to fix this fault by requesting a quote

Browse other Massey Ferguson codes