Massey Ferguson 3226.19 – Engine Control Unit (ECU): NOx Sensor Outlet SCR Signal Issue
Issue description
The Engine Control Module (ECM) is receiving invalid or erroneous data from the outlet NOx sensor over the CAN bus network (indicated by FMI 19). This sensor measures nitrogen oxide concentrations downstream of the Selective Catalytic Reduction (SCR) catalyst. A signal failure affects the proper functioning of the emissions control system's ability to manage DEF injection, which can lead to check engine light illumination, reduced engine performance or power, increased fuel consumption, and the machine entering a derated or limp mode to limit emissions.
Applies to these machines
46 machines- 4710
- 7724S
- 5712SL
- 7722S
- 7722
- 5713SL
- 7720S
- 7716
- 7718
- T4
- 7715
- 5710SL
- 7726
- 4708
- 7726S
- 4707
- 4709
- 5711SL
- 7718S
- 7719
- 7714
- 7716S
- T4 (2015-2021)
- 7720
- Tier 4 (2015-2021)
- 7715S
- 7724
- 5611
- 5612
- 5613
- 5709
- 5710
- 5711
- 5712
- 5713
- 6612
- 6613
- 6614
- 6615
- 6616
- 8727
- 8730
- 8732
- 8735
- 8737
- 8740
Check the cause
Clear the error log using a diagnostic tool, restart the ECU, and cycle the key to see if the fault returns
Physically inspect the wiring harness leading to the downstream NOx sensor, checking connectors and pin contact surfaces for oxidation, corrosion, or physical damage
Monitor live data with a diagnostic tool to compare sensor data; if the downstream NOx reading is completely flat or implausible while the upstream NOx sensor responds normally to engine load, the downstream sensor is faulty
Plug in a known good test NOx sensor to verify if communication is restored before permanently installing a new one
Repair steps
Preparation
Turn off the tractor, remove the key, and allow the exhaust system to cool completely. Disconnect the battery to prevent electrical spikes.
Locate the Sensor
Locate the downstream NOx sensor, which is installed directly into the exhaust pipe downstream of the Selective Catalytic Reduction (SCR) catalyst.
Removal
Disconnect the 5-pin electrical connector. Carefully unthread the sensor from the exhaust pipe.
Installation Precautions
Do not touch the ceramic probe of the new sensor with your bare fingers, as oil contamination will cause premature failure. Do not use an impact wrench to install the sensor, as this will damage the threads and void the warranty.
Install the New Sensor
Thread the new sensor into the exhaust pipe using a new sealing washer. Tighten to the manufacturer's specified torque.
Reconnect
Plug in the electrical connector and ensure it clicks securely into place.
Clear Codes
Reconnect the battery, turn on the ignition, and use a diagnostic tool to clear the 003226.19 fault code. Run the tractor through a drive cycle to ensure the code does not return.
Parts you might need
(7)12V, 5-pin unit with an M20x1.5 thread. Always verify the exact part number against your machine's serial number due to different cable lengths.
Often listed as an interchangeable or superseded number
Used on many 4700, 5700, 6700, and 7700 series models
Downstream Nitrogen Oxide (NOx) Sensor / NOx Sensor Outlet SCR
5WK96622COEM Manufacturer Part Number (Manufactured by Continental / Vitesco UniNOx for AGCO)
Outlet NOx Sensor
ACW1813980Verify fitment by serial number.
- Outlet NOx SensorACX248097A
Verify fitment by serial number.
Outlet NOx Sensor
72661028Verify fitment by serial number.
Get help to fix this fault by requesting a quote