Massey Ferguson 3228.14 – Engine Control Unit (ECU): Issue With Supply Voltage To NOx Sensor Outlet SCR
Issue description
The engine control module has detected that the supply voltage to the downstream (outlet) NOx sensor is outside its expected range. This sensor measures the concentration of nitrogen oxides in the exhaust gas after the SCR catalyst to verify emissions reduction efficiency. A power supply issue prevents the sensor from operating correctly, leading to inaccurate readings or signal loss. This condition prevents the SCR system from verifying its performance, typically resulting in an illuminated warning lamp and a significant engine power derate to ensure emissions compliance.
Applies to these machines
42 machines- 4710
- 7724S
- 5712SL
- 7722S
- 7722
- 5713SL
- 7720S
- 7716
- 7718
- T4
- 7715
- 5710SL
- 7726
- 4708
- 7726S
- 4707
- 4709
- 5711SL
- 7718S
- 7719
- 7714
- 7716S
- T4 (2015-2021)
- 7720
- Tier 4 (2015-2021)
- 7715S
- 7724
- 5608
- 5609
- 5610
- 5611
- 5612
- 5613
- 7614
- 7615
- 7616
- 7618
- 7619
- 7620
- 7622
- 7624
- 7626
Check the cause
Check the fuse and relay assortment for the after-treatment circuits to rule out intermittent voltage drops or blown fuses.
Inspect the wiring harness routing to the downstream NOx sensor for signs of heat soak, melting, or vibration damage.
Use a multimeter at the NOx sensor connector to verify if the supply voltage is actually out of range or if the circuit is open.
Check the SCR outlet gasket and clamps for exhaust leaks, which can skew NOx readings and trigger plausibility faults.
Inspect the pins on the ECU and the sensor connector for corrosion, moisture, or poor contact.
Repair steps
Power Down
Turn off the tractor and disconnect the battery to ensure safety and prevent short circuits during the repair.
Locate the Sensor
Locate the downstream NOx sensor, which is positioned on the exhaust pipe after the SCR catalytic converter.
Disconnect
Unplug the electrical connector for the NOx sensor.
Remove
Carefully unscrew and remove the faulty NOx sensor from the exhaust pipe. (Penetrating oil may be required if the threads are seized from exhaust heat).
Install
Thread the new NOx sensor into the exhaust pipe and tighten it to the manufacturer's specified torque.
Route the Harness
Crucial step: Route the new NOx sensor harness exactly like the factory routing to avoid future heat soak and vibration failures.
Reconnect
Plug in the electrical connector and reconnect the battery.
Clear Codes
Use an AGCO diagnostic tool (EDT) to clear the fault code (003228.14 / SPN 3228 FMI 14) and run the engine to verify the sensor is reading correctly and the code does not return.
Parts you might need
(11)- NOx Sensor (Downstream / Outlet SCR)V837084094
AGCO / Massey Ferguson / Valtra / Fendt
- NOx Sensor (Downstream / Outlet SCR)ACW1305320
AGCO / Massey Ferguson / Valtra / Fendt
- NOx Sensor (Downstream / Outlet SCR)ACX248097A
AGCO / Massey Ferguson / Valtra / Fendt
- NOx Sensor (Downstream / Outlet SCR)ACX2480970
AGCO / Massey Ferguson / Valtra / Fendt
NOx Sensor (Downstream / Outlet SCR)
ACW1813980AGCO / Massey Ferguson / Valtra / Fendt
NOx Sensor (Downstream / Outlet SCR)
ACP0677370AGCO / Massey Ferguson / Valtra / Fendt
- NOx Sensor (Downstream / Outlet SCR)F835970020021
Fendt equivalent, often cross-compatible within AGCO brands
NOx Sensor (Downstream / Outlet SCR)
0281008262Bosch OEM
NOx Sensor (Downstream / Outlet SCR)
0281008263Bosch OEM
Outlet NOx Sensor
72661028OEM part number. Verify fitment by serial number.
Outlet NOx Sensor (Aftermarket)
QTP-65117Fits Massey Ferguson 5700, 6700, 7700 Series.
Get help to fix this fault by requesting a quote