4344.04

Massey Ferguson 4344.04 – Engine Control Unit (ECU): DEF Unit Internal Temperature Sensor Issue (ECU)

Issue description

The fault code indicates a problem with the internal temperature sensor within the Diesel Exhaust Fluid (DEF) unit, as detected by the Engine Control Unit (ECU). This sensor is critical for the Selective Catalytic Reduction (SCR) system to properly manage the DEF system, which can freeze at 12°F (-11°C) or break down if too hot. A malfunctioning sensor can prevent the DEF tank heater from activating in cold weather, cause the ECU to enter a protective limp mode reducing engine power, and trigger an emissions warning light.

Applies to these machines

  • 4710
  • 7724S
  • 5712SL
  • Interim Tier 4 (2012-2015)
  • 7722
  • 7722S
  • 7615
  • 5613
  • 5713SL
  • 7720S
  • 7716
  • 7718
  • T4
  • 7715
  • 5710SL
  • 7726
  • 7616
  • 7618
  • 5608
  • 4708
  • 7619
  • 7626
  • 7726S
  • 7624
  • 4707
  • 4709
  • 5711SL
  • 7614
  • 7718S
  • 5610
  • 7620
  • 7719
  • 7714
  • 7716S
  • T4 (2015-2021)
  • 5612
  • 7622
  • 7720
  • Tier 4 (2015-2021)
  • 5611
  • 7715S
  • 5609
  • 7724

Check the cause

  1. Inspect the wiring harness and the main electrical connector at the top of the DEF tank header for rubbed wires, corrosion, or moisture inside the connector pins.

  2. Use a diagnostic scan tool to read the live DEF tank temperature. If the reading shows an impossible extreme (e.g., -40°C or +200°C), the internal sensor is shorted or open.

  3. Verify that the tractor's Ambient Air Temperature sensor is reading correctly, as a failed ambient air temp sensor can disable the DEF system and trigger erratic DEF temperature fault codes.

  4. Check for DEF fluid leaking out of the header O-ring and crystallizing on the electrical connector, which can destroy the sensor's circuitry.

Repair steps

  1. Preparation

    Turn off the tractor, disconnect the battery, and thoroughly clean the top of the DEF tank around the header assembly to prevent dirt from falling into the tank.

  2. Disconnect Lines

    Carefully disconnect the DEF supply and return lines from the header. Note: These are heated lines with quick connectors and O-rings. Cap them immediately to prevent contamination and do not kink them.

  3. Disconnect Electrical

    Unplug the CANbus/electrical connector from the DEF header.

  4. Remove Header

    Unscrew the locking ring or retaining bolts holding the DEF header to the tank. Carefully pull the header assembly straight up and out of the tank.

  5. Install New Part

    Insert the new DEF header assembly, ensuring the new rubber gasket/O-ring is seated perfectly to prevent dust and moisture ingress.

  6. Reassembly

    Tighten the locking ring/bolts. Reconnect the heated DEF lines (ensure they click into place) and the electrical connector.

  7. Clear Codes

    Reconnect the battery, turn the ignition on, and use a diagnostic tool to clear the 004344.04 code and reset the aftertreatment system.

Parts you might need

(14)
  • AGCO / Massey Ferguson OEM DEF Sensor Assembly

    ACW0251030

    Always verify the exact part number against your tractor's specific serial number via an AGCO dealer.

  • Alternative AGCO OEM Part

    4351064M2

    Often listed for specific Massey Ferguson/Fendt emission systems.

  • DEF Tank Header Assembly / Urea Quality Level Sensor (UQLS) / DEF Sending Unit

    Generic part names.

  • Common for Sisu Diesel engines

  • Alternative module depending on exact fitment

  • DEF Supply Module (Pump)

    ARX2983200

    Alternative module depending on exact fitment

  • DEF Sensor (Level/Temp/Quality)

    ASP01DS22-FF

    DuraWRX aftermarket digital CANbus option

  • AGCO OEM

  • DEF Supply Module Filter

    72666873

    Alternative listing for H218PF153008B

  • AGCO OEM

  • DEF Dosing Module / Injector

    0444023011

    Bosch OEM (if related replacement is needed)

  • AGCO OEM (if related replacement is needed)

  • Listed as compatible with many models, but described as a cylinder head/fuel temp sensor; verify applicability for DEF system before use.

  • DEF Sensor

    ACW288799A

    Related AGCO DEF system part; direct application to resolve this specific fault code is unconfirmed.

Get help to fix this fault by requesting a quote

Browse other Massey Ferguson codes