655.13

Massey Ferguson 655.13 – Engine ECU: Injector Number 5 Calibration Code Issue

Issue description

The Engine Control Unit (ECU) has detected that the unique calibration code for fuel injector number 5 is missing, incorrect, or corrupted in its memory. Modern common rail diesel injectors have specific calibration codes that fine-tune their performance for precise fuel delivery. Without the correct calibration data programmed into the ECU, the engine may experience suboptimal performance, rough running, poor fuel economy, or increased emissions.

Applies to these machines

  • 4710
  • 7724S
  • Interim Tier 4 (2012-2015)
  • 7722S
  • 7722
  • 7615
  • 7720S
  • 7716
  • 7718
  • 7726
  • 7715
  • 7616
  • 7618
  • 4708
  • 7619
  • 7626
  • 7726S
  • 7624
  • 4707
  • 4709
  • 7614
  • 7718S
  • 7620
  • 7719
  • 7714
  • 7716S
  • T4 (2015-2021)
  • 7622
  • 7720
  • Tier 4 (2015-2021)
  • 7715S
  • 7724
  • 4700 series
  • T4 models from 2015-2021
  • 7600 series
  • 7700 series
  • 8700 series

Check the cause

  1. Verify if the #5 fuel injector was recently replaced without programming the new calibration code into the ECU

  2. Read the ECU memory using an OEM-level diagnostic scan tool (such as AGCO EDT) to check the currently stored code for Cylinder 5

  3. Physically locate the #5 fuel injector and read the alphanumeric calibration code stamped on the top, then compare it to the stored ECU code

  4. Check for ECU power loss or software glitches if the injector was not recently replaced

Repair steps

  1. Access the Injector

    Remove any engine covers necessary to clearly see the top of the #5 fuel injector.

  2. Record the Code

    Write down the alphanumeric calibration/trim code printed on the injector head.

  3. Connect Diagnostic Tool

    Plug your AGCO EDT (or equivalent capable scan tool) into the tractor's diagnostic port.

  4. Program the ECU

    Navigate to the Engine ECU -> Injector Calibration / Programming menu.

  5. Enter the Code

    Select Cylinder #5 and input the exact alphanumeric code you recorded from the injector. Save the configuration to the ECU.

  6. Clear and Test

    Clear the active 000655.13 fault code. Cycle the tractor's ignition key off for 30 seconds, then turn it back on and start the engine.

  7. Replace if Necessary

    If the ECU refuses to accept the code, the ECU software may need to be reflashed. If the injector itself has failed mechanically or electrically, you must replace the injector and then program the new injector's code into the ECU.

Parts you might need

(7)
  • Bosch Mfg No: 0445110408. You must verify the exact part number against your specific tractor's serial number. Never mix genuine and aftermarket injectors on the same engine. Always replace the copper sealing washer and O-rings when installing a new injector.

  • Fuel Injector (7600 & 8600 Series)

    V837073713

    Manufactured by Bosch, Part # 0445120235

  • Injector Connector Tube (7600 & 8600 Series)

    F00RJ02717

    Bosch part, sold separately, highly recommended to replace alongside the injector

  • Manufactured by Bosch, Part # 0445124025

  • Injector Connector Tube (7700, 6700S, & 8700S Series)

    F00RC00584

    Bosch part

  • Fuel Injector (Bosch Cross-Reference)

    0445110408

    Bosch cross-reference part number.

  • Fuel Injector (AGCO Cross-Reference)

    837073791

    AGCO cross-reference part number.

Get help to fix this fault by requesting a quote

Browse other Massey Ferguson codes