94

Massey Ferguson 94 – ECU: Oil Filter Pressure Low

Issue description

The engine's control system has detected that the voltage signal from the fuel filter pressure sensor is below the normal operating range. This indicates that the fuel pressure measured before or at the fuel filter is lower than the manufacturer's specification. This condition is most commonly caused by restricted fuel flow due to clogged fuel filters or the gelling of diesel fuel in cold weather.

Applies to these machines

  • 3050
  • 3060
  • 3065
  • 3075
  • 3085
  • 3095
  • 3120
  • 3125
  • 3635
  • 3645
  • 3655
  • 3670
  • 3690
  • 4225
  • 4235
  • 4240
  • 4245
  • 4255
  • 4260
  • 4265
  • 4270
  • 4325
  • 4335
  • 4345
  • 4355
  • 4360
  • 4365
  • 4370
  • 5445
  • 5455
  • 5460
  • 5465
  • 6110
  • 6120
  • 6130
  • 6140
  • 6150
  • 6160
  • 6170
  • 6180
  • 6190
  • 6235
  • 6245
  • 6255
  • 6260
  • 6265
  • 6270
  • 6280
  • 6290
  • 6445
  • 6455
  • 6460
  • 6465
  • 6470
  • 6475
  • 6480
  • 6485
  • 6490
  • 6495
  • 6497
  • 6499
  • 7465
  • 7475
  • 7480
  • 7485
  • 7490
  • 7495
  • 8110
  • 8120
  • 8130
  • 8140
  • 8150
  • 8160
  • 8170
  • 8210
  • 8220
  • 8240
  • 8250
  • 8260
  • 8270
  • 8280
  • 8450
  • 8460
  • 8470
  • 8600 Series

Check the cause

  1. Verify the engine oil is at the correct level, as low oil levels can cause a drop in pressure

  2. Inspect the engine for any signs of oil leaks from hoses or seals

  3. Check the condition of the engine oil and the oil filter for dirt, contamination, or clogging that could impede flow

  4. Inspect the electrical connector and wiring to the oil filter pressure sensor for damage, corrosion, or loose connections

  5. Connect a mechanical pressure gauge to the fully warmed-up engine to measure actual oil pressure and confirm if the warning is accurate or a sensor error

Repair steps

  1. Confirm the fault

    After performing initial checks, use a mechanical gauge to confirm if low pressure actually exists. If the mechanical gauge shows good pressure, the issue is likely with the sensor or wiring.

  2. Address low-pressure causes

    If true low pressure is confirmed by the mechanical gauge, investigate and repair internal mechanical issues such as a worn oil pump, a faulty pressure regulator valve, or a leaking oil pickup tube O-ring inside the oil pan.

  3. Replace the sensor

    If mechanical pressure is good but the code persists, replace the oil filter pressure sensor. Unplug the electrical connector, unscrew the old sensor, ensure sealing surfaces are clean, install the new sensor, and torque to the manufacturer's specification.

  4. Clear codes and test

    Clear the fault code from the ECU using a diagnostic tool and run the engine to ensure the code does not reappear.

Parts you might need

(2)
  • OEM AGCO Parts. High-precision sensor for monitoring the engine's lubrication system.

  • OEM AGCO Power (formerly SisuDiesel) part. Widely used on Sisu/AGCO Power Tier 3 and Tier 4 engines.

Get help to fix this fault by requesting a quote

Browse other Massey Ferguson codes